diff options
-rw-r--r-- | firmware/target/arm/imx233/powermgmt-imx233.c | 41 |
1 files changed, 15 insertions, 26 deletions
diff --git a/firmware/target/arm/imx233/powermgmt-imx233.c b/firmware/target/arm/imx233/powermgmt-imx233.c index 7a1ea8338e..01d0e3eae1 100644 --- a/firmware/target/arm/imx233/powermgmt-imx233.c +++ b/firmware/target/arm/imx233/powermgmt-imx233.c @@ -58,35 +58,13 @@ void imx233_powermgmt_init(void) BF_WR(POWER_VDDDCTRL, LINREG_OFFSET, 2); BF_WR(POWER_VDDACTRL, LINREG_OFFSET, 2); BF_WR(POWER_VDDIOCTRL, LINREG_OFFSET, 2); - /* enable DCDC (more efficient) */ - BF_SET(POWER_5VCTRL, ENABLE_DCDC); - BF_CLR(POWER_5VCTRL, DCDC_XFER); -#else - BF_SET(POWER_5VCTRL, LINREG_OFFSET); - BF_SET(POWER_5VCTRL, EN_DCDC1); - BF_SET(POWER_5VCTRL, EN_DCDC2); -#endif - -#if IMX233_SUBTARGET >= 3780 - /* adjust arbitration between 4.2 and battery */ - BF_WR(POWER_DCDC4P2, CMPTRIP, 0); /* 85% */ - BF_WR(POWER_DCDC4P2, DROPOUT_CTRL, 0xe); /* select greater, 200 mV drop */ -#endif - -#if IMX233_SUBTARGET >= 3700 /* enable a few bits controlling the DC-DC as recommended by Freescale */ BF_SET(POWER_LOOPCTRL, TOGGLE_DIF); BF_SET(POWER_LOOPCTRL, EN_CM_HYST); BF_CLR(POWER_LOOPCTRL, EN_RCSCALE); BF_SETV(POWER_LOOPCTRL, EN_RCSCALE, 1); - /* make sure we are in a known state: disable charger */ - BF_SET(POWER_CHARGE, PWD_BATTCHRG); -#endif -#if IMX233_SUBTARGET >= 3780 - /* make sure we are in a known state: disable 4p2 */ - BF_WR(POWER_DCDC4P2, ENABLE_DCDC, 0); - BF_WR(POWER_DCDC4P2, ENABLE_4P2, 0); - BF_SET(POWER_5VCTRL, PWD_CHARGE_4P2); +#else + BF_SET(POWER_5VCTRL, LINREG_OFFSET); #endif } @@ -110,6 +88,7 @@ void charging_algorithm_step(void) #if IMX233_SUBTARGET >= 3780 BF_WR(POWER_DCDC4P2, ENABLE_DCDC, 0); BF_WR(POWER_DCDC4P2, ENABLE_4P2, 0); + BF_WR(POWER_5VCTRL, CHARGE_4P2_ILIMIT, 1); BF_SET(POWER_5VCTRL, PWD_CHARGE_4P2); #endif charge_state = DISCHARGING; @@ -120,10 +99,14 @@ void charging_algorithm_step(void) logf("pwrmgmt: discharging -> trickle"); logf("pwrmgmt: begin charging 4p2"); #if IMX233_SUBTARGET >= 3780 - /* 5V has been detected: prepare 4.2V power rail for activation */ + /* 5V has been detected: prepare 4.2V power rail for activation + * WARNING we can reach this situation when starting after Freescale bootloader + * or after RoLo in a state where the DCDC is running. In this case, + * we must *NOT* disable it or this will shutdown the device. This procedure + * is safe: it will never disable the DCDC and will not reduce the charge + * limit on the 4P2 rail. */ BF_WR(POWER_DCDC4P2, ENABLE_4P2, 1); BF_SET(POWER_CHARGE, ENABLE_LOAD); - BF_WR(POWER_5VCTRL, CHARGE_4P2_ILIMIT, 1); BF_CLR(POWER_5VCTRL, PWD_CHARGE_4P2);// FIXME: manual error ? BF_WR(POWER_DCDC4P2, ENABLE_DCDC, 1); #endif @@ -147,6 +130,12 @@ void charging_algorithm_step(void) { logf("pwrmgmt: enable dcdc and charger"); logf("pwrmgmt: trickle -> charging"); +#if IMX233_SUBTARGET >= 3780 + /* adjust arbitration between 4.2 and battery */ + BF_WR(POWER_DCDC4P2, CMPTRIP, 0); /* 85% */ + BF_WR(POWER_DCDC4P2, DROPOUT_CTRL, 0xe); /* select greater, 200 mV drop */ +#endif + /* switch to DCDC */ BF_CLR(POWER_5VCTRL, DCDC_XFER); BF_SET(POWER_5VCTRL, ENABLE_DCDC); /* enable battery charging */ |