summaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
authorCástor Muñoz <cmvidal@gmail.com>2016-05-14 14:24:49 +0200
committerCástor Muñoz <cmvidal@gmail.com>2016-05-14 19:39:09 +0200
commit9a4cd2eaee7d389f2fa6e0d79f0f6ea526f7ef85 (patch)
tree2cf04d46c512cf48d05c1804e03aee952885bf47
parent60fb707203c5b0ce2c32776890611846f0c22566 (diff)
downloadrockbox-9a4cd2eaee7d389f2fa6e0d79f0f6ea526f7ef85.tar.gz
rockbox-9a4cd2eaee7d389f2fa6e0d79f0f6ea526f7ef85.zip
iPod Nano2G: add IPOD_ACCESSORY_PROTOCOL
Change-Id: I78a19972624504bc802d96b9b8e9cec132164c2c
-rw-r--r--firmware/export/config/ipodnano2g.h9
-rw-r--r--firmware/export/s5l8700.h52
-rw-r--r--firmware/target/arm/s5l8700/ipodnano2g/serial-nano2g.c113
-rw-r--r--firmware/target/arm/s5l8700/system-s5l8700.c12
-rw-r--r--firmware/target/arm/s5l8700/uart-s5l8701.c17
5 files changed, 183 insertions, 20 deletions
diff --git a/firmware/export/config/ipodnano2g.h b/firmware/export/config/ipodnano2g.h
index a9c7239056..8e8f40f56c 100644
--- a/firmware/export/config/ipodnano2g.h
+++ b/firmware/export/config/ipodnano2g.h
@@ -231,9 +231,14 @@
/* Define this if you can switch on/off the accessory power supply */
#define HAVE_ACCESSORY_SUPPLY
-//#define IPOD_ACCESSORY_PROTOCOL
-#ifdef LOGF_SERIAL
+
+/* Serial */
+#ifndef BOOTLOADER
#define HAVE_SERIAL
+/* Disable iAP when LOGF_SERIAL is enabled to avoid conflicts */
+#ifndef LOGF_SERIAL
+#define IPOD_ACCESSORY_PROTOCOL
+#endif
#endif
/* Define this, if you can switch on/off the lineout */
diff --git a/firmware/export/s5l8700.h b/firmware/export/s5l8700.h
index e8497ff337..3444919bc3 100644
--- a/firmware/export/s5l8700.h
+++ b/firmware/export/s5l8700.h
@@ -133,33 +133,61 @@
#define PWRCONEXT (*(REG32_PTR_T)(0x3C500040)) /* Clock power control register 2 */
/* 06. INTERRUPT CONTROLLER UNIT */
+#if CONFIG_CPU==S5L8700
#define SRCPND (*(REG32_PTR_T)(0x39C00000)) /* Indicates the interrupt request status. */
#define INTMOD (*(REG32_PTR_T)(0x39C00004)) /* Interrupt mode register. */
#define INTMSK (*(REG32_PTR_T)(0x39C00008)) /* Determines which interrupt source is masked. The */
-#if CONFIG_CPU==S5L8701
-#define INTMSK_TIMERA (1<<5)
-#define INTMSK_TIMERB (1<<5)
-#define INTMSK_TIMERC (1<<5)
-#define INTMSK_TIMERD (1<<5)
-#define INTMSK_ECC (1<<19)
-#define INTMSK_USB_OTG (1<<16)
-#define INTMSK_UART0 (0) /* Unknown */
-#define INTMSK_UART1 (1<<12)
-#define INTMSK_UART2 (1<<7)
-#else
#define INTMSK_TIMERA (1<<5)
#define INTMSK_TIMERB (1<<7)
#define INTMSK_TIMERC (1<<8)
#define INTMSK_TIMERD (1<<9)
#define INTMSK_UART0 (1<<22)
#define INTMSK_UART1 (1<<14)
-#endif
#define PRIORITY (*(REG32_PTR_T)(0x39C0000C)) /* IRQ priority control register */
#define INTPND (*(REG32_PTR_T)(0x39C00010)) /* Indicates the interrupt request status. */
#define INTOFFSET (*(REG32_PTR_T)(0x39C00014)) /* Indicates the IRQ interrupt request source */
#define EINTPOL (*(REG32_PTR_T)(0x39C00018)) /* Indicates external interrupt polarity */
#define EINTPEND (*(REG32_PTR_T)(0x39C0001C)) /* Indicates whether external interrupts are pending. */
#define EINTMSK (*(REG32_PTR_T)(0x39C00020)) /* Indicates whether external interrupts are masked */
+#else /* S5L8701 */
+#define SRCPND (*(REG32_PTR_T)(0x39C00000)) /* Indicates the interrupt request status. */
+#define INTMOD (*(REG32_PTR_T)(0x39C00004)) /* Interrupt mode register. */
+#define INTMSK (*(REG32_PTR_T)(0x39C00008)) /* Determines which interrupt source is masked. The */
+#define INTMSK_EINTG0 (1<<1)
+#define INTMSK_EINTG1 (1<<2)
+#define INTMSK_EINTG2 (1<<3)
+#define INTMSK_EINTG3 (1<<4)
+#define INTMSK_TIMERA (1<<5)
+#define INTMSK_TIMERB (1<<5)
+#define INTMSK_TIMERC (1<<5)
+#define INTMSK_TIMERD (1<<5)
+#define INTMSK_ECC (1<<19)
+#define INTMSK_USB_OTG (1<<16)
+#define INTMSK_UART0 (0) /* (AFAIK) no IRQ to ICU, uses EINTG0 */
+#define INTMSK_UART1 (1<<12)
+#define INTMSK_UART2 (1<<7)
+#define PRIORITY (*(REG32_PTR_T)(0x39C0000C)) /* IRQ priority control register */
+#define INTPND (*(REG32_PTR_T)(0x39C00010)) /* Indicates the interrupt request status. */
+#define INTOFFSET (*(REG32_PTR_T)(0x39C00014)) /* Indicates the IRQ interrupt request source */
+/*
+ * s5l8701 GPIO (External) Interrupt Controller.
+ *
+ * At first glance it looks very similar to gpio-s5l8702, but
+ * not fully tested, so this information could be wrong.
+ *
+ * Group0[31:10] Not used
+ * [9] UART0 IRQ
+ * [8] VBUS
+ * [7:0] PDAT1
+ * Group1[31:0] PDAT5:PDAT4:PDAT3:PDAT2
+ * Group2[31:0] PDAT11:PDAT10:PDAT7:PDAT6
+ * Group3[31:0] PDAT15:PDAT14:PDAT13:PDAT12
+ */
+#define GPIOIC_INTLEVEL(g) (*(REG32_PTR_T)(0x39C00018 + 4*(g)))
+#define GPIOIC_INTSTAT(g) (*(REG32_PTR_T)(0x39C00028 + 4*(g)))
+#define GPIOIC_INTEN(g) (*(REG32_PTR_T)(0x39C00038 + 4*(g)))
+#define GPIOIC_INTTYPE(g) (*(REG32_PTR_T)(0x39C00048 + 4*(g)))
+#endif
/* 07. MEMORY INTERFACE UNIT (MIU) */
diff --git a/firmware/target/arm/s5l8700/ipodnano2g/serial-nano2g.c b/firmware/target/arm/s5l8700/ipodnano2g/serial-nano2g.c
index 487984fbe3..5ff0b0ca25 100644
--- a/firmware/target/arm/s5l8700/ipodnano2g/serial-nano2g.c
+++ b/firmware/target/arm/s5l8700/ipodnano2g/serial-nano2g.c
@@ -47,6 +47,9 @@
extern const struct uartc s5l8701_uartc0;
+#ifdef IPOD_ACCESSORY_PROTOCOL
+void iap_rx_isr(int, char*, char*, uint32_t);
+#endif
struct uartc_port ser_port IDATA_ATTR =
{
@@ -61,7 +64,11 @@ struct uartc_port ser_port IDATA_ATTR =
.clkhz = NANO2G_UART_CLK_HZ,
/* interrupt callbacks */
+#ifdef IPOD_ACCESSORY_PROTOCOL
+ .rx_cb = iap_rx_isr,
+#else
.rx_cb = NULL,
+#endif
.tx_cb = NULL, /* polling */
};
@@ -94,3 +101,109 @@ void tx_writec(unsigned char c)
{
uartc_port_tx_byte(&ser_port, c);
}
+
+
+#ifdef IPOD_ACCESSORY_PROTOCOL
+#include "iap.h"
+
+static enum {
+ ABR_STATUS_LAUNCHED, /* ST_SYNC */
+ ABR_STATUS_SYNCING, /* ST_SOF */
+ ABR_STATUS_DONE
+} abr_status;
+
+void serial_bitrate(int rate)
+{
+ logf("[%lu] serial_bitrate(%d)", (uint32_t)USEC_TIMER, rate);
+
+ if (rate == 0) {
+ /* Using auto-bitrate (ABR) to detect accessory Tx speed:
+ *
+ * + Here:
+ * - Disable Rx logic to clean the FIFO and the shift
+ * register, thus no Rx data interrupts are generated.
+ * - Launch ABR and wait for a low pulse in Rx line.
+ *
+ * + In ISR, when a low pulse is detected (ideally it is the
+ * start bit of 0xff):
+ * - Calculate and configure detected speed.
+ * - Enable Rx to verify that the next received data frame
+ * is 0x55 or 0xff:
+ * - If so, it's assumed bit rate is correctly detected,
+ * it will not be modified until speed is changed using
+ * RB options menu.
+ * - If not, reset iAP state machine and launch a new ABR.
+ */
+ uartc_port_set_rx_mode(&ser_port, UCON_MODE_DISABLED);
+ uartc_port_abr_start(&ser_port);
+ abr_status = ABR_STATUS_LAUNCHED;
+ }
+ else {
+ uint32_t brdata;
+ if (rate == 57600) brdata = BRDATA_57600;
+ else if (rate == 38400) brdata = BRDATA_38400;
+ else if (rate == 19200) brdata = BRDATA_19200;
+ else brdata = BRDATA_9600;
+ uartc_port_abr_stop(&ser_port); /* abort ABR if already launched */
+ uartc_port_set_bitrate_raw(&ser_port, brdata);
+ uartc_port_set_rx_mode(&ser_port, UCON_MODE_INTREQ);
+ abr_status = ABR_STATUS_DONE;
+ }
+}
+
+void iap_rx_isr(int len, char *data, char *err, uint32_t abr_cnt)
+{
+ /* ignore Rx errors, upper layer will discard bad packets */
+ (void) err;
+
+ static int sync_retry;
+
+ if (abr_status == ABR_STATUS_LAUNCHED) {
+ /* autobauding */
+ if (abr_cnt) {
+ #define BR2CNT(s) (NANO2G_UART_CLK_HZ / (unsigned)(s))
+ if (abr_cnt < BR2CNT(57600*1.1) || abr_cnt > BR2CNT(9600*0.9)) {
+ /* detected speed out of range, relaunch ABR */
+ uartc_port_abr_start(&ser_port);
+ return;
+ }
+ /* valid speed detected, select it */
+ uint32_t brdata;
+ if (abr_cnt < BR2CNT(48000)) brdata = BRDATA_57600;
+ else if (abr_cnt < BR2CNT(33600)) brdata = BRDATA_38400;
+ else if (abr_cnt < BR2CNT(24000)) brdata = BRDATA_28800;
+ else if (abr_cnt < BR2CNT(14400)) brdata = BRDATA_19200;
+ else brdata = BRDATA_9600;
+
+ /* set detected speed */
+ uartc_port_set_bitrate_raw(&ser_port, brdata);
+ uartc_port_set_rx_mode(&ser_port, UCON_MODE_INTREQ);
+
+ /* enter SOF state */
+ iap_getc(0xff);
+
+ abr_status = ABR_STATUS_SYNCING;
+ sync_retry = 2; /* we are expecting [0xff] 0x55 */
+ }
+ }
+
+ /* process received data */
+ while (len--)
+ {
+ bool sync_done = !iap_getc(*data++);
+
+ if (abr_status == ABR_STATUS_SYNCING)
+ {
+ if (sync_done) {
+ abr_status = ABR_STATUS_DONE;
+ }
+ else if (--sync_retry == 0) {
+ /* invalid speed detected, relaunch ABR
+ discarding remaining data (if any) */
+ serial_bitrate(0);
+ break;
+ }
+ }
+ }
+}
+#endif /* IPOD_ACCESSORY_PROTOCOL */
diff --git a/firmware/target/arm/s5l8700/system-s5l8700.c b/firmware/target/arm/s5l8700/system-s5l8700.c
index 728fea0432..226464fb08 100644
--- a/firmware/target/arm/s5l8700/system-s5l8700.c
+++ b/firmware/target/arm/s5l8700/system-s5l8700.c
@@ -85,6 +85,10 @@ default_interrupt(INT_ADC);
#if CONFIG_CPU==S5L8701
default_interrupt(INT_UNK);
default_interrupt(INT_UART2);
+default_interrupt(EINT_G0);
+default_interrupt(EINT_G1);
+default_interrupt(EINT_G2);
+default_interrupt(EINT_G3);
#endif
@@ -99,8 +103,8 @@ void INT_TIMER(void)
#if CONFIG_CPU==S5L8701
static void (* const irqvector[])(void) =
-{ /* still 90% unverified and probably incorrect */
- EXT0,EXT1,EXT2,EINT_VBUS,EINTG,INT_TIMER,INT_WDT,INT_UART2,
+{ /* still 80% unverified and probably incorrect */
+ EXT0,EINT_G0,EINT_G1,EINT_G2,EINT_G3,INT_TIMER,INT_WDT,INT_UART2,
INT_UNK,INT_UNK,INT_DMA,INT_ALARM_RTC,INT_UART1,INT_UNK,INT_UNK,INT_USB_HOST,
INT_USB_FUNC,INT_LCDC_0,INT_LCDC_1,INT_CALM,INT_ATA,INT_UNK,INT_SPDIF_OUT,INT_ECC,
INT_SDCI,INT_LCD,INT_WHEEL,INT_IIC,RESERVED2,INT_MSTICK,INT_ADC_WAKEUP,INT_ADC
@@ -117,8 +121,8 @@ static void (* const irqvector[])(void) =
#if CONFIG_CPU==S5L8701
static const char * const irqname[] =
-{ /* still 90% unverified and probably incorrect */
- "EXT0","EXT1","EXT2","EINT_VBUS","EINTG","INT_TIMER","INT_WDT","INT_UART2",
+{ /* still 80% unverified and probably incorrect */
+ "EXT0","EINT_G0","EINT_G1","EINT_G2","EINT_G3","INT_TIMER","INT_WDT","INT_UART2",
"INT_UNK1","INT_UNK2","INT_DMA","INT_ALARM_RTC","INT_UART1","INT_UNK3","INT_UNK4","INT_USB_HOST",
"INT_USB_FUNC","INT_LCDC_0","INT_LCDC_1","INT_CALM","INT_ATA","INT_UNK5","INT_SPDIF_OUT","INT_ECC",
"INT_SDCI","INT_LCD","INT_WHEEL","INT_IIC","Reserved","INT_MSTICK","INT_ADC_WAKEUP","INT_ADC"
diff --git a/firmware/target/arm/s5l8700/uart-s5l8701.c b/firmware/target/arm/s5l8700/uart-s5l8701.c
index 00c9322e47..b9fb1632ac 100644
--- a/firmware/target/arm/s5l8700/uart-s5l8701.c
+++ b/firmware/target/arm/s5l8700/uart-s5l8701.c
@@ -68,7 +68,7 @@ static uint8_t clockgate_uartc[S5L8701_N_UARTC] = {
CLOCKGATE_UARTC0, CLOCKGATE_UARTC1, CLOCKGATE_UARTC2 };
static int intmsk_uart[S5L8701_N_UARTC] = {
- INTMSK_UART0, INTMSK_UART1, INTMSK_UART2 };
+ INTMSK_EINTG0, INTMSK_UART1, INTMSK_UART2 };
/*
* Device level functions specific to S5L8701
@@ -107,6 +107,7 @@ void uart_target_disable_gpio(int uart_id, int port_id)
void uart_target_enable_irq(int uart_id, int port_id)
{
(void) port_id;
+ if (uart_id == 0) GPIOIC_INTEN(0) = 0x200;
INTMSK |= intmsk_uart[uart_id];
}
@@ -114,11 +115,13 @@ void uart_target_disable_irq(int uart_id, int port_id)
{
(void) port_id;
INTMSK &= ~intmsk_uart[uart_id];
+ if (uart_id == 0) GPIOIC_INTEN(0) = 0;
}
void uart_target_clear_irq(int uart_id, int port_id)
{
(void) port_id;
+ if (uart_id == 0) GPIOIC_INTSTAT(0) = 0x200;
SRCPND |= intmsk_uart[uart_id];
}
@@ -135,10 +138,20 @@ void uart_target_disable_clocks(int uart_id)
/*
* ISRs
*/
-void ICODE_ATTR INT_UART0(void)
+
+/* On Nano2G, PORT0 interrupts are not used when iAP is disabled */
+#if !defined(IPOD_NANO2G) || defined(IPOD_ACCESSORY_PROTOCOL)
+/*
+ * UART0 IRQ is connected to EINTG0, this is a quick patch, a "real"
+ * EINT handler will be needed if in future we use more than one IRQ
+ * on this group.
+ */
+void ICODE_ATTR EINT_G0(void)
{
+ GPIOIC_INTSTAT(0) = 0x200; /* clear external IRQ */
uartc_callback(&s5l8701_uartc0, 0);
}
+#endif
/* UARTC1,2 not used on Nano2G */
#ifndef IPOD_NANO2G