summaryrefslogtreecommitdiffstats
path: root/firmware/target/mips
diff options
context:
space:
mode:
Diffstat (limited to 'firmware/target/mips')
-rw-r--r--firmware/target/mips/ingenic_x1000/erosqnative/button-erosqnative.c10
-rw-r--r--firmware/target/mips/ingenic_x1000/erosqnative/power-erosqnative.c82
-rw-r--r--firmware/target/mips/ingenic_x1000/fiiom3k/button-fiiom3k.c8
-rw-r--r--firmware/target/mips/ingenic_x1000/fiiom3k/power-fiiom3k.c80
-rw-r--r--firmware/target/mips/ingenic_x1000/shanlingq1/button-shanlingq1.c8
-rw-r--r--firmware/target/mips/ingenic_x1000/shanlingq1/power-shanlingq1.c70
6 files changed, 87 insertions, 171 deletions
diff --git a/firmware/target/mips/ingenic_x1000/erosqnative/button-erosqnative.c b/firmware/target/mips/ingenic_x1000/erosqnative/button-erosqnative.c
index 64041795a3..1583db175a 100644
--- a/firmware/target/mips/ingenic_x1000/erosqnative/button-erosqnative.c
+++ b/firmware/target/mips/ingenic_x1000/erosqnative/button-erosqnative.c
@@ -24,7 +24,7 @@
#include "backlight.h"
#include "powermgmt.h"
#include "panic.h"
-#include "axp192.h"
+#include "axp-pmu.h"
#include "gpio-x1000.h"
#include "irq-x1000.h"
#include "i2c-x1000.h"
@@ -89,7 +89,7 @@ static int hp_detect_tmo_cb(struct timeout* tmo)
static void hp_detect_init(void)
{
static struct timeout tmo;
- static const uint8_t gpio_reg = AXP_REG_GPIOLEVEL1;
+ static const uint8_t gpio_reg = AXP192_REG_GPIOSTATE1;
static i2c_descriptor desc = {
.slave_addr = AXP_PMU_ADDR,
.bus_cond = I2C_START | I2C_STOP,
@@ -105,11 +105,11 @@ static void hp_detect_init(void)
/* Headphone and LO detects are wired to AXP192 GPIOs 0 and 1,
* set them to inputs. */
- axp_set_gpio_function(0, AXP_GPIO_INPUT); /* HP detect */
- axp_set_gpio_function(1, AXP_GPIO_INPUT); /* LO detect */
+ i2c_reg_write1(AXP_PMU_BUS, AXP_PMU_ADDR, AXP192_REG_GPIO0FUNCTION, 0x01); /* HP detect */
+ i2c_reg_write1(AXP_PMU_BUS, AXP_PMU_ADDR, AXP192_REG_GPIO1FUNCTION, 0x01); /* LO detect */
/* Get an initial reading before startup */
- int r = axp_read(gpio_reg);
+ int r = i2c_reg_read1(AXP_PMU_BUS, AXP_PMU_ADDR, gpio_reg);
if(r >= 0)
{
hp_detect_reg = r;
diff --git a/firmware/target/mips/ingenic_x1000/erosqnative/power-erosqnative.c b/firmware/target/mips/ingenic_x1000/erosqnative/power-erosqnative.c
index 9cf64cee01..a1a4d2c2b2 100644
--- a/firmware/target/mips/ingenic_x1000/erosqnative/power-erosqnative.c
+++ b/firmware/target/mips/ingenic_x1000/erosqnative/power-erosqnative.c
@@ -28,7 +28,7 @@
#ifdef HAVE_USB_CHARGING_ENABLE
# include "usb_core.h"
#endif
-#include "axp192.h"
+#include "axp-pmu.h"
#include "i2c-x1000.h"
const unsigned short battery_level_dangerous[BATTERY_TYPES_COUNT] =
@@ -56,35 +56,27 @@ const unsigned short percent_to_volt_charge[11] =
void power_init(void)
{
- /* Configure I2C bus */
- i2c_x1000_set_freq(AXP_PMU_BUS, I2C_FREQ_400K);
-
- /* FIXME: Copy paste from M3K. Probably not necessary */
- axp_modify(AXP_REG_DCDCMODE, 0, 0xc0);
-
- /* Power on required supplies
- * TODO: This should be checked, though likely all but EXTEN are needed */
- axp_set_enabled_supplies(
- (1 << AXP_SUPPLY_EXTEN) |
- (1 << AXP_SUPPLY_DCDC1) |
- (1 << AXP_SUPPLY_DCDC2) |
- (1 << AXP_SUPPLY_DCDC3) |
- (1 << AXP_SUPPLY_LDO2) |
- (1 << AXP_SUPPLY_LDO3));
-
- /* Enable required ADCs */
- axp_set_enabled_adcs(
- (1 << AXP_ADC_BATTERY_VOLTAGE) |
- (1 << AXP_ADC_CHARGE_CURRENT) |
- (1 << AXP_ADC_DISCHARGE_CURRENT) |
- (1 << AXP_ADC_VBUS_VOLTAGE) |
- (1 << AXP_ADC_VBUS_CURRENT) |
- (1 << AXP_ADC_INTERNAL_TEMP) |
- (1 << AXP_ADC_APS_VOLTAGE));
-
- /* Configure USB charging */
- axp_set_vhold_level(4400);
- usb_charging_maxcurrent_change(100);
+ /* Initialize driver */
+ i2c_x1000_set_freq(2, I2C_FREQ_400K);
+ axp_init();
+
+ /* Set lowest sample rate */
+ axp_adc_set_rate(AXP_ADC_RATE_25HZ);
+
+ /* Ensure battery voltage ADC is enabled */
+ int bits = axp_adc_get_enabled();
+ bits |= (1 << ADC_BATTERY_VOLTAGE);
+ axp_adc_set_enabled(bits);
+
+ /* Turn on all power outputs */
+ i2c_reg_modify1(AXP_PMU_BUS, AXP_PMU_ADDR,
+ AXP_REG_PWROUTPUTCTRL2, 0, 0x5f, NULL);
+ i2c_reg_modify1(AXP_PMU_BUS, AXP_PMU_ADDR,
+ AXP_REG_DCDCWORKINGMODE, 0, 0xc0, NULL);
+
+ /* Set the default charging current. This is the same as the
+ * OF's setting, although it's not strictly within the USB spec. */
+ axp_set_charge_current(780);
/* Delay to give power outputs time to stabilize.
* With the power thread delay, this can apparently go as low as 50,
@@ -96,22 +88,7 @@ void power_init(void)
#ifdef HAVE_USB_CHARGING_ENABLE
void usb_charging_maxcurrent_change(int maxcurrent)
{
- int vbus_limit;
- int charge_current;
-
- /* Note that the charge current setting is a maximum: it will be
- * reduced dynamically by the AXP192 so the combined load is less
- * than the set VBUS current limit. */
- if(maxcurrent <= 100) {
- vbus_limit = AXP_VBUS_LIMIT_500mA;
- charge_current = 100;
- } else {
- vbus_limit = AXP_VBUS_LIMIT_500mA;
- charge_current = 550;
- }
-
- axp_set_vbus_limit(vbus_limit);
- axp_set_charge_current(charge_current);
+ axp_set_charge_current(maxcurrent);
}
#endif
@@ -127,25 +104,20 @@ void power_off(void)
bool charging_state(void)
{
- return axp_is_charging();
-}
-
-unsigned int power_input_status(void)
-{
- return axp_power_input_status();
+ return axp_battery_status() == AXP_BATT_CHARGING;
}
int _battery_voltage(void)
{
- return axp_read_adc(AXP_ADC_BATTERY_VOLTAGE);
+ return axp_adc_read(ADC_BATTERY_VOLTAGE);
}
#if CONFIG_BATTERY_MEASURE & CURRENT_MEASURE
int _battery_current(void)
{
if(charging_state())
- return axp_read_adc(AXP_ADC_CHARGE_CURRENT);
+ return axp_adc_read(ADC_CHARGE_CURRENT);
else
- return axp_read_adc(AXP_ADC_DISCHARGE_CURRENT);
+ return axp_adc_read(ADC_DISCHARGE_CURRENT);
}
#endif
diff --git a/firmware/target/mips/ingenic_x1000/fiiom3k/button-fiiom3k.c b/firmware/target/mips/ingenic_x1000/fiiom3k/button-fiiom3k.c
index 0ef7bd2f64..24daf2ef69 100644
--- a/firmware/target/mips/ingenic_x1000/fiiom3k/button-fiiom3k.c
+++ b/firmware/target/mips/ingenic_x1000/fiiom3k/button-fiiom3k.c
@@ -24,7 +24,7 @@
#include "backlight.h"
#include "powermgmt.h"
#include "panic.h"
-#include "axp192.h"
+#include "axp-pmu.h"
#include "ft6x06.h"
#include "gpio-x1000.h"
#include "irq-x1000.h"
@@ -393,7 +393,7 @@ static int hp_detect_tmo_cb(struct timeout* tmo)
static void hp_detect_init(void)
{
static struct timeout tmo;
- static const uint8_t gpio_reg = AXP_REG_GPIOLEVEL1;
+ static const uint8_t gpio_reg = AXP192_REG_GPIOSTATE1;
static i2c_descriptor desc = {
.slave_addr = AXP_PMU_ADDR,
.bus_cond = I2C_START | I2C_STOP,
@@ -408,10 +408,10 @@ static void hp_detect_init(void)
};
/* Headphone detect is wired to AXP192 GPIO: set it to input state */
- axp_set_gpio_function(2, AXP_GPIO_INPUT);
+ i2c_reg_write1(AXP_PMU_BUS, AXP_PMU_ADDR, AXP192_REG_GPIO2FUNCTION, 0x01);
/* Get an initial reading before startup */
- int r = axp_read(gpio_reg);
+ int r = i2c_reg_read1(AXP_PMU_BUS, AXP_PMU_ADDR, gpio_reg);
if(r >= 0)
hp_detect_reg = r;
diff --git a/firmware/target/mips/ingenic_x1000/fiiom3k/power-fiiom3k.c b/firmware/target/mips/ingenic_x1000/fiiom3k/power-fiiom3k.c
index b20bbd9e8c..2d28ad0975 100644
--- a/firmware/target/mips/ingenic_x1000/fiiom3k/power-fiiom3k.c
+++ b/firmware/target/mips/ingenic_x1000/fiiom3k/power-fiiom3k.c
@@ -26,7 +26,7 @@
#ifdef HAVE_USB_CHARGING_ENABLE
# include "usb_core.h"
#endif
-#include "axp192.h"
+#include "axp-pmu.h"
#include "i2c-x1000.h"
const unsigned short battery_level_dangerous[BATTERY_TYPES_COUNT] =
@@ -54,33 +54,27 @@ const unsigned short percent_to_volt_charge[11] =
void power_init(void)
{
- /* Configure I2C bus */
- i2c_x1000_set_freq(AXP_PMU_BUS, I2C_FREQ_400K);
-
- /* Set DCDC1 and DCDC2 to fixed PWM mode to match OF settings. */
- axp_modify(AXP_REG_DCDCMODE, 0, 0x0c);
-
- /* Power on required supplies */
- axp_set_enabled_supplies(
- (1 << AXP_SUPPLY_DCDC1) | /* not sure (3.3 V) */
- (1 << AXP_SUPPLY_DCDC2) | /* not sure (1.4 V) */
- (1 << AXP_SUPPLY_DCDC3) | /* for CPU (1.8 V) */
- (1 << AXP_SUPPLY_LDO2) | /* LCD controller (3.3 V) */
- (1 << AXP_SUPPLY_LDO3)); /* SD bus (3.3 V) */
-
- /* Enable required ADCs */
- axp_set_enabled_adcs(
- (1 << AXP_ADC_BATTERY_VOLTAGE) |
- (1 << AXP_ADC_CHARGE_CURRENT) |
- (1 << AXP_ADC_DISCHARGE_CURRENT) |
- (1 << AXP_ADC_VBUS_VOLTAGE) |
- (1 << AXP_ADC_VBUS_CURRENT) |
- (1 << AXP_ADC_INTERNAL_TEMP) |
- (1 << AXP_ADC_APS_VOLTAGE));
-
- /* Configure USB charging */
- axp_set_vhold_level(4400);
- usb_charging_maxcurrent_change(100);
+ /* Initialize driver */
+ i2c_x1000_set_freq(2, I2C_FREQ_400K);
+ axp_init();
+
+ /* Set lowest sample rate */
+ axp_adc_set_rate(AXP_ADC_RATE_25HZ);
+
+ /* Ensure battery voltage ADC is enabled */
+ int bits = axp_adc_get_enabled();
+ bits |= (1 << ADC_BATTERY_VOLTAGE);
+ axp_adc_set_enabled(bits);
+
+ /* Turn on all power outputs */
+ i2c_reg_modify1(AXP_PMU_BUS, AXP_PMU_ADDR,
+ AXP_REG_PWROUTPUTCTRL2, 0, 0x5f, NULL);
+ i2c_reg_modify1(AXP_PMU_BUS, AXP_PMU_ADDR,
+ AXP_REG_DCDCWORKINGMODE, 0, 0xc0, NULL);
+
+ /* Set the default charging current. This is the same as the
+ * OF's setting, although it's not strictly within the USB spec. */
+ axp_set_charge_current(780);
/* Short delay to give power outputs time to stabilize */
mdelay(200);
@@ -89,22 +83,7 @@ void power_init(void)
#ifdef HAVE_USB_CHARGING_ENABLE
void usb_charging_maxcurrent_change(int maxcurrent)
{
- int vbus_limit;
- int charge_current;
-
- /* Note that the charge current setting is a maximum: it will be
- * reduced dynamically by the AXP192 so the combined load is less
- * than the set VBUS current limit. */
- if(maxcurrent <= 100) {
- vbus_limit = AXP_VBUS_LIMIT_500mA;
- charge_current = 100;
- } else {
- vbus_limit = AXP_VBUS_LIMIT_500mA;
- charge_current = 550;
- }
-
- axp_set_vbus_limit(vbus_limit);
- axp_set_charge_current(charge_current);
+ axp_set_charge_current(maxcurrent);
}
#endif
@@ -120,25 +99,20 @@ void power_off(void)
bool charging_state(void)
{
- return axp_is_charging();
-}
-
-unsigned int power_input_status(void)
-{
- return axp_power_input_status();
+ return axp_battery_status() == AXP_BATT_CHARGING;
}
int _battery_voltage(void)
{
- return axp_read_adc(AXP_ADC_BATTERY_VOLTAGE);
+ return axp_adc_read(ADC_BATTERY_VOLTAGE);
}
#if CONFIG_BATTERY_MEASURE & CURRENT_MEASURE
int _battery_current(void)
{
if(charging_state())
- return axp_read_adc(AXP_ADC_CHARGE_CURRENT);
+ return axp_adc_read(ADC_CHARGE_CURRENT);
else
- return axp_read_adc(AXP_ADC_DISCHARGE_CURRENT);
+ return axp_adc_read(ADC_DISCHARGE_CURRENT);
}
#endif
diff --git a/firmware/target/mips/ingenic_x1000/shanlingq1/button-shanlingq1.c b/firmware/target/mips/ingenic_x1000/shanlingq1/button-shanlingq1.c
index 1976dde793..13b0cdd078 100644
--- a/firmware/target/mips/ingenic_x1000/shanlingq1/button-shanlingq1.c
+++ b/firmware/target/mips/ingenic_x1000/shanlingq1/button-shanlingq1.c
@@ -23,7 +23,7 @@
#include "button.h"
#include "touchscreen.h"
#include "ft6x06.h"
-#include "axp192.h"
+#include "axp-pmu.h"
#include "kernel.h"
#include "backlight.h"
#include "powermgmt.h"
@@ -57,7 +57,7 @@ static void hp_detect_init(void)
{
/* TODO: replace this copy paste cruft with an API in axp-pmu */
static struct timeout tmo;
- static const uint8_t gpio_reg = AXP_REG_GPIOLEVEL1;
+ static const uint8_t gpio_reg = AXP192_REG_GPIOSTATE1;
static i2c_descriptor desc = {
.slave_addr = AXP_PMU_ADDR,
.bus_cond = I2C_START | I2C_STOP,
@@ -72,10 +72,10 @@ static void hp_detect_init(void)
};
/* Headphone detect is wired to AXP192 GPIO: set it to input state */
- axp_set_gpio_function(1, AXP_GPIO_INPUT);
+ i2c_reg_write1(AXP_PMU_BUS, AXP_PMU_ADDR, AXP192_REG_GPIO1FUNCTION, 0x01);
/* Get an initial reading before startup */
- int r = axp_read(gpio_reg);
+ int r = i2c_reg_read1(AXP_PMU_BUS, AXP_PMU_ADDR, gpio_reg);
if(r >= 0)
hp_detect_reg = r;
diff --git a/firmware/target/mips/ingenic_x1000/shanlingq1/power-shanlingq1.c b/firmware/target/mips/ingenic_x1000/shanlingq1/power-shanlingq1.c
index 86ee84c37a..75f8031dd9 100644
--- a/firmware/target/mips/ingenic_x1000/shanlingq1/power-shanlingq1.c
+++ b/firmware/target/mips/ingenic_x1000/shanlingq1/power-shanlingq1.c
@@ -22,7 +22,7 @@
#include "power.h"
#include "adc.h"
#include "system.h"
-#include "axp192.h"
+#include "axp-pmu.h"
#ifdef HAVE_CW2015
# include "cw2015.h"
#endif
@@ -73,34 +73,24 @@ const unsigned short percent_to_volt_charge[11] =
void power_init(void)
{
i2c_x1000_set_freq(AXP_PMU_BUS, I2C_FREQ_400K);
+ axp_init();
#ifdef HAVE_CW2015
cw2015_init();
#endif
- /* Set DCDC2 to 1.2 V to match OF settings. */
- axp_set_supply_voltage(AXP_SUPPLY_DCDC2, 1200);
-
- /* Power on required supplies */
- axp_set_enabled_supplies(
- (1 << AXP_SUPPLY_DCDC1) | /* SD bus (3.3 V) */
- (1 << AXP_SUPPLY_DCDC2) | /* LCD (1.2 V) */
- (1 << AXP_SUPPLY_DCDC3) | /* CPU (1.8 V) */
- (1 << AXP_SUPPLY_LDO2) | /* Touchscreen (3.3 V) */
- (1 << AXP_SUPPLY_LDO3)); /* USB analog (2.5 V) */
-
- /* Enable required ADCs */
- axp_set_enabled_adcs(
- (1 << AXP_ADC_BATTERY_VOLTAGE) |
- (1 << AXP_ADC_CHARGE_CURRENT) |
- (1 << AXP_ADC_DISCHARGE_CURRENT) |
- (1 << AXP_ADC_VBUS_VOLTAGE) |
- (1 << AXP_ADC_VBUS_CURRENT) |
- (1 << AXP_ADC_INTERNAL_TEMP) |
- (1 << AXP_ADC_APS_VOLTAGE));
-
- /* Configure USB charging */
- axp_set_vhold_level(4400);
- usb_charging_maxcurrent_change(100);
+ /* Change supply voltage from the default of 1250 mV to 1200 mV,
+ * this matches the original firmware's settings. Didn't observe
+ * any obviously bad behavior at 1250 mV, but better to be safe. */
+ axp_supply_set_voltage(AXP_SUPPLY_DCDC2, 1200);
+
+ /* For now, just turn everything on... definitely the touchscreen
+ * is powered by one of the outputs */
+ i2c_reg_modify1(AXP_PMU_BUS, AXP_PMU_ADDR,
+ AXP_REG_PWROUTPUTCTRL1, 0, 0x05, NULL);
+ i2c_reg_modify1(AXP_PMU_BUS, AXP_PMU_ADDR,
+ AXP_REG_PWROUTPUTCTRL2, 0, 0x0f, NULL);
+ i2c_reg_modify1(AXP_PMU_BUS, AXP_PMU_ADDR,
+ AXP_REG_DCDCWORKINGMODE, 0, 0xc0, NULL);
/* Delay to give power output time to stabilize */
mdelay(20);
@@ -109,22 +99,7 @@ void power_init(void)
#ifdef HAVE_USB_CHARGING_ENABLE
void usb_charging_maxcurrent_change(int maxcurrent)
{
- int vbus_limit;
- int charge_current;
-
- /* Note that the charge current setting is a maximum: it will be
- * reduced dynamically by the AXP192 so the combined load is less
- * than the set VBUS current limit. */
- if(maxcurrent <= 100) {
- vbus_limit = AXP_VBUS_LIMIT_500mA;
- charge_current = 100;
- } else {
- vbus_limit = AXP_VBUS_LIMIT_500mA;
- charge_current = 550;
- }
-
- axp_set_vbus_limit(vbus_limit);
- axp_set_charge_current(charge_current);
+ axp_set_charge_current(maxcurrent);
}
#endif
@@ -136,28 +111,23 @@ void power_off(void)
bool charging_state(void)
{
- return axp_is_charging();
-}
-
-unsigned int power_input_status(void)
-{
- return axp_power_input_status();
+ return axp_battery_status() == AXP_BATT_CHARGING;
}
int _battery_voltage(void)
{
/* CW2015 can also read battery voltage, but the AXP consistently
* reads ~20-30 mV higher so I suspect it's the "real" voltage. */
- return axp_read_adc(AXP_ADC_BATTERY_VOLTAGE);
+ return axp_adc_read(ADC_BATTERY_VOLTAGE);
}
#if CONFIG_BATTERY_MEASURE & CURRENT_MEASURE
int _battery_current(void)
{
if(charging_state())
- return axp_read_adc(AXP_ADC_CHARGE_CURRENT);
+ return axp_adc_read(ADC_CHARGE_CURRENT);
else
- return axp_read_adc(AXP_ADC_DISCHARGE_CURRENT);
+ return axp_adc_read(ADC_DISCHARGE_CURRENT);
}
#endif