/*************************************************************************** * __________ __ ___. * Open \______ \ ____ ____ | | _\_ |__ _______ ___ * Source | _// _ \_/ ___\| |/ /| __ \ / _ \ \/ / * Jukebox | | ( <_> ) \___| < | \_\ ( <_> > < < * Firmware |____|_ /\____/ \___ >__|_ \|___ /\____/__/\_ \ * \/ \/ \/ \/ \/ * $Id$ * * Copyright (C) 2011 by Amaury Pouly * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License * as published by the Free Software Foundation; either version 2 * of the License, or (at your option) any later version. * * This software is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY * KIND, either express or implied. * ****************************************************************************/ #include "config.h" #include "system.h" #include "sd.h" #include "mmc.h" #include "sdmmc.h" #include "ssp-imx233.h" #include "pinctrl-imx233.h" #include "partitions-imx233.h" #include "button-target.h" #include "fat.h" #include "disk.h" #include "usb.h" #include "debug.h" #include "string.h" #include "ata_idle_notify.h" /** NOTE For convenience, this drivers relies on the many similar commands * between SD and MMC. The following assumptions are made: * - SD_SEND_STATUS = MMC_SEND_STATUS * - SD_SELECT_CARD = MMC_SELECT_CARD * - SD_TRAN = MMC_TRAN * - MMC_WRITE_MULTIPLE_BLOCK = SD_WRITE_MULTIPLE_BLOCK * - MMC_READ_MULTIPLE_BLOCK = SD_READ_MULTIPLE_BLOCK * - SD_STOP_TRANSMISSION = MMC_STOP_TRANSMISSION * - SD_DESELECT_CARD = MMC_DESELECT_CARD */ #if SD_SEND_STATUS != MMC_SEND_STATUS || SD_SELECT_CARD != MMC_SELECT_CARD || \ SD_TRAN != MMC_TRAN || MMC_WRITE_MULTIPLE_BLOCK != SD_WRITE_MULTIPLE_BLOCK || \ MMC_READ_MULTIPLE_BLOCK != SD_READ_MULTIPLE_BLOCK || \ SD_STOP_TRANSMISSION != MMC_STOP_TRANSMISSION || \ SD_DESELECT_CARD != MMC_DESELECT_CARD #error SD/MMC mismatch #endif struct sdmmc_config_t { const char *name; /* name(for debug) */ int flags; /* flags */ int power_pin; /* power pin */ int power_delay; /* extra power up delay */ int ssp; /* associated ssp block */ int mode; /* mode (SD vs MMC) */ }; /* flags */ #define POWER_PIN (1 << 0) #define POWER_INVERTED (1 << 1) #define REMOVABLE (1 << 2) #define DETECT_INVERTED (1 << 3) #define POWER_DELAY (1 << 4) #define WINDOW (1 << 5) /* modes */ #define SD_MODE 0 #define MMC_MODE 1 #define PIN(bank,pin) ((bank) << 5 | (pin)) #define PIN2BANK(v) ((v) >> 5) #define PIN2PIN(v) ((v) & 0x1f) struct sdmmc_config_t sdmmc_config[] = { #ifdef SANSA_FUZEPLUS /* The Fuze+ uses pin #B0P8 for power */ { .name = "microSD", .flags = POWER_PIN | POWER_INVERTED | REMOVABLE, .power_pin = PIN(0, 8), .ssp = 1, .mode = SD_MODE, }, /* The Fuze+ uses pin #B1P29 for power */ { .name = "eMMC", .flags = POWER_PIN | POWER_INVERTED | WINDOW | POWER_DELAY, .power_pin = PIN(1, 29), .power_delay = HZ / 5, /* extra delay, to ramp up voltage? */ .ssp = 2, .mode = MMC_MODE, }, #elif defined(CREATIVE_ZENXFI2) /* The Zen X-Fi2 uses pin B1P29 for power*/ { .name = "microSD", .flags = POWER_PIN | REMOVABLE | DETECT_INVERTED, .power_pin = PIN(1, 29), .ssp = 1, .mode = SD_MODE, }, #elif defined(CREATIVE_ZENXFI3) { .name = "internal/SD", .flags = WINDOW, .ssp = 2, .mode = SD_MODE, }, /* The Zen X-Fi3 uses pin #B0P07 for power*/ { .name = "microSD", .flags = POWER_PIN | POWER_INVERTED | REMOVABLE | POWER_DELAY, .power_pin = PIN(0, 7), .power_delay = HZ / 10, /* extra delay, to ramp up voltage? */ .ssp = 1, .mode = SD_MODE, }, #else #error You need to write the sd/mmc config! #endif }; #define SDMMC_NUM_DRIVES (sizeof(sdmmc_config) / sizeof(sdmmc_config[0])) #define SDMMC_CONF(drive) sdmmc_config[drive] #define SDMMC_FLAGS(drive) SDMMC_CONF(drive).flags #define SDMMC_SSP(drive) SDMMC_CONF(drive).ssp #define SDMMC_MODE(drive) SDMMC_CONF(drive).mode /** WARNING * to be consistent with all our SD drivers, the .rca field of sdmmc_card_info * in reality holds (rca << 16) because all command arguments actually require * the RCA is the 16-bit msb. Be careful that this is not the actuall RCA ! */ /* common */ static unsigned window_start[SDMMC_NUM_DRIVES]; static unsigned window_end[SDMMC_NUM_DRIVES]; static uint8_t aligned_buffer[SDMMC_NUM_DRIVES][512] CACHEALIGN_ATTR; static tCardInfo sdmmc_card_info[SDMMC_NUM_DRIVES]; static struct mutex mutex[SDMMC_NUM_DRIVES]; static int disk_last_activity[SDMMC_NUM_DRIVES]; #define MIN_YIELD_PERIOD 5 /* ticks */ static int next_yield = 0; #define SDMMC_INFO(drive) sdmmc_card_info[drive] #define SDMMC_RCA(drive) SDMMC_INFO(drive).rca /* sd only */ static long sdmmc_stack[(DEFAULT_STACK_SIZE*2 + 0x200)/sizeof(long)]; static const char sdmmc_thread_name[] = "sdmmc"; static struct event_queue sdmmc_queue; #if CONFIG_STORAGE & STORAGE_SD static int sd_first_drive; static unsigned _sd_num_drives; static int sd_map[SDMMC_NUM_DRIVES]; /* sd->sdmmc map */ #endif /* mmc only */ #if CONFIG_STORAGE & STORAGE_MMC static int mmc_first_drive; static unsigned _mmc_num_drives; static int mmc_map[SDMMC_NUM_DRIVES]; /* mmc->sdmmc map */ #endif /* WARNING NOTE BUG FIXME * There are three numbering schemes involved in the driver: * - the sdmmc indexes into sdmmc_config[] * - the sd drive indexes * - the mmc drive indexes * By convention, [drive] refers to a sdmmc index whereas sd_drive/mmc_drive * refer to sd/mmc drive indexes. We keep two maps sd->sdmmc and mmc->sdmmc * to find the sdmmc index from the sd or mmc one */ static void sdmmc_detect_callback(int ssp) { /* This is called only if the state was stable for 300ms - check state * and post appropriate event. */ if(imx233_ssp_sdmmc_detect(ssp)) queue_broadcast(SYS_HOTSWAP_INSERTED, 0); else queue_broadcast(SYS_HOTSWAP_EXTRACTED, 0); imx233_ssp_sdmmc_setup_detect(ssp, true, sdmmc_detect_callback, false, imx233_ssp_sdmmc_is_detect_inverted(ssp)); } static void sdmmc_power(int drive, bool on) { /* power chip if needed */ if(SDMMC_FLAGS(drive) & POWER_PIN) { int bank = PIN2BANK(SDMMC_CONF(drive).power_pin); int pin = PIN2PIN(SDMMC_CONF(drive).power_pin); imx233_pinctrl_acquire_pin(bank, pin, "sd/mmc power"); imx233_set_pin_function(bank, pin, PINCTRL_FUNCTION_GPIO); imx233_enable_gpio_output(bank, pin, true); if(SDMMC_FLAGS(drive) & POWER_INVERTED) imx233_set_gpio_output(bank, pin, !on); else imx233_set_gpio_output(bank, pin, on); } if(SDMMC_FLAGS(drive) & POWER_DELAY) sleep(SDMMC_CONF(drive).power_delay); /* setup pins, never use alternatives pin on SSP1 because no device use it * but this could be made a flag */ int bus_width = SDMMC_MODE(drive) == MMC_MODE ? 8 : 4; if(SDMMC_SSP(drive) == 1) imx233_ssp_setup_ssp1_sd_mmc_pins(on, bus_width, PINCTRL_DRIVE_4mA, false); else imx233_ssp_setup_ssp2_sd_mmc_pins(on, bus_width, PINCTRL_DRIVE_4mA); } #define MCI_NO_RESP 0 #define MCI_RESP (1<<0) #define MCI_LONG_RESP (1<<1) #define MCI_ACMD (1<<2) /* sd only */ #define MCI_NOCRC (1<<3) #define MCI_BUSY (1<<4) static bool send_cmd(int drive, uint8_t cmd, uint32_t arg, uint32_t flags, uint32_t *resp) { if((flags & MCI_ACMD) && !send_cmd(drive, SD_APP_CMD, SDMMC_RCA(drive), MCI_RESP, resp)) return false; enum imx233_ssp_resp_t resp_type = (flags & MCI_LONG_RESP) ? SSP_LONG_RESP : (flags & MCI_RESP) ? SSP_SHORT_RESP : SSP_NO_RESP; enum imx233_ssp_error_t ret = imx233_ssp_sd_mmc_transfer(SDMMC_SSP(drive), cmd, arg, resp_type, NULL, 0, !!(flags & MCI_BUSY), false, resp); if(resp_type == SSP_LONG_RESP) { /* Our SD codes assume most significant word first, so reverse resp */ uint32_t tmp = resp[0]; resp[0] = resp[3]; resp[3] = tmp; tmp = resp[1]; resp[1] = resp[2]; resp[2] = tmp; } return ret == SSP_SUCCESS; } static int wait_for_state(int drive, unsigned state) { unsigned long response; unsigned int timeout = current_tick + 5*HZ; int cmd_retry = 10; while (1) { /* NOTE: rely on SD_SEND_STATUS=MMC_SEND_STATUS */ while(!send_cmd(drive, SD_SEND_STATUS, SDMMC_RCA(drive), MCI_RESP, &response) && cmd_retry > 0) cmd_retry--; if(cmd_retry <= 0) return -1; if(((response >> 9) & 0xf) == state) return 0; if(TIME_AFTER(current_tick, timeout)) return -10 * ((response >> 9) & 0xf); if(TIME_AFTER(current_tick, next_yield)) { yield(); next_yield = current_tick + MIN_YIELD_PERIOD; } } return 0; } #if CONFIG_STORAGE & STORAGE_SD static int init_sd_card(int drive) { int ssp = SDMMC_SSP(drive); sdmmc_power(drive, false); sdmmc_power(drive, true); imx233_ssp_start(ssp); imx233_ssp_softreset(ssp); imx233_ssp_set_mode(ssp, HW_SSP_CTRL1__SSP_MODE__SD_MMC); /* SSPCLK @ 96MHz * gives bitrate of 96000 / 240 / 1 = 400kHz */ imx233_ssp_set_timings(ssp, 240, 0, 0xffff); imx233_ssp_sd_mmc_power_up_sequence(ssp); imx233_ssp_set_bus_width(ssp, 1); imx233_ssp_set_block_size(ssp, 9); SDMMC_RCA(drive) = 0; bool sd_v2 = false; uint32_t resp; long init_timeout; /* go to idle state */ if(!send_cmd(drive, SD_GO_IDLE_STATE, 0, MCI_NO_RESP, NULL)) return -1; /* CMD8 Check for v2 sd card. Must be sent before using ACMD41 Non v2 cards will not respond to this command */ if(send_cmd(drive, SD_SEND_IF_COND, 0x1AA, MCI_RESP, &resp)) if((resp & 0xFFF) == 0x1AA) sd_v2 = true; /* timeout for initialization is 1sec, from SD Specification 2.00 */ init_timeout = current_tick + HZ; do { /* this timeout is the only valid error for this loop*/ if(TIME_AFTER(current_tick, init_timeout)) return -2; /* ACMD41 For v2 cards set HCS bit[30] & send host voltage range to all */ if(!send_cmd(drive, SD_APP_OP_COND, (0x00FF8000 | (sd_v2 ? 1<<30 : 0)), MCI_ACMD|MCI_NOCRC|MCI_RESP, &SDMMC_INFO(drive).ocr)) return -100; } while(!(SDMMC_INFO(drive).ocr & (1<<31))); /* CMD2 send CID */ if(!send_cmd(drive, SD_ALL_SEND_CID, 0, MCI_RESP|MCI_LONG_RESP, SDMMC_INFO(drive).cid)) return -3; /* CMD3 send RCA */ if(!send_cmd(drive, SD_SEND_RELATIVE_ADDR, 0, MCI_RESP, &SDMMC_INFO(drive).rca)) return -4; /* Try to switch V2 cards to HS timings, non HS seem to ignore this */ if(sd_v2) { /* CMD7 w/rca: Select card to put it in TRAN state */ if(!send_cmd(drive, SD_SELECT_CARD, SDMMC_RCA(drive), MCI_RESP, NULL)) return -5; if(wait_for_state(drive, SD_TRAN)) return -6; /* CMD6 */ if(!send_cmd(drive, SD_SWITCH_FUNC, 0x80fffff1, MCI_NO_RESP, NULL)) return -7; sleep(HZ/10); /* go back to STBY state so we can read csd */ /* CMD7 w/rca=0: Deselect card to put it in STBY state */ if(!send_cmd(drive, SD_DESELECT_CARD, 0, MCI_NO_RESP, NULL)) return -8; } /* CMD9 send CSD */ if(!send_cmd(drive, SD_SEND_CSD, SDMMC_RCA(drive), MCI_RESP|MCI_LONG_RESP, SDMMC_INFO(drive).csd)) return -9; sd_parse_csd(&SDMMC_INFO(drive)); window_start[drive] = 0; window_end[drive] = SDMMC_INFO(drive).numblocks; /* SSPCLK @ 96MHz * gives bitrate of 96 / 4 / 1 = 24MHz */ imx233_ssp_set_timings(ssp, 4, 0, 0xffff); /* CMD7 w/rca: Select card to put it in TRAN state */ if(!send_cmd(drive, SD_SELECT_CARD, SDMMC_RCA(drive), MCI_RESP, &resp)) return -12; if(wait_for_state(drive, SD_TRAN)) return -13; /* ACMD6: set bus width to 4-bit */ if(!send_cmd(drive, SD_SET_BUS_WIDTH, 2, MCI_RESP|MCI_ACMD, &resp)) return -15; /* ACMD42: disconnect the pull-up resistor on CD/DAT3 */ if(!send_cmd(drive, SD_SET_CLR_CARD_DETECT, 0, MCI_RESP|MCI_ACMD, &resp)) return -17; /* Switch to 4-bit */ imx233_ssp_set_bus_width(ssp, 4); SDMMC_INFO(drive).initialized = 1; return 0; } #endif #if CONFIG_STORAGE & STORAGE_MMC static int init_mmc_drive(int drive) { int ssp = SDMMC_SSP(drive); /* we can choose the RCA of mmc cards: pick drive. Following our convention, * .rca is actually RCA << 16 */ SDMMC_RCA(drive) = drive << 16; sdmmc_power(drive, false); sdmmc_power(drive, true); imx233_ssp_start(ssp); imx233_ssp_softreset(ssp); imx233_ssp_set_mode(ssp, HW_SSP_CTRL1__SSP_MODE__SD_MMC); /* SSPCLK @ 96MHz * gives bitrate of 96000 / 240 / 1 = 400kHz */ imx233_ssp_set_timings(ssp, 240, 0, 0xffff); imx233_ssp_sd_mmc_power_up_sequence(ssp); imx233_ssp_set_bus_width(ssp, 1); imx233_ssp_set_block_size(ssp, 9); /* go to idle state */ if(!send_cmd(drive, MMC_GO_IDLE_STATE, 0, MCI_NO_RESP, NULL)) return -1; /* send op cond until the card respond with busy bit set; it must complete within 1sec */ unsigned timeout = current_tick + HZ; bool ret = false; do { uint32_t ocr; ret = send_cmd(drive, MMC_SEND_OP_COND, 0x40ff8000, MCI_RESP, &ocr); if(ret && ocr & (1 << 31)) break; }while(!TIME_AFTER(current_tick, timeout)); if(!ret) return -2; /* get CID */ uint32_t cid[4]; if(!send_cmd(drive, MMC_ALL_SEND_CID, 0, MCI_LONG_RESP, cid)) return -3; /* Set RCA */ uint32_t status; if(!send_cmd(drive, MMC_SET_RELATIVE_ADDR, SDMMC_RCA(drive), MCI_RESP, &status)) return -4; /* Select card */ if(!send_cmd(drive, MMC_SELECT_CARD, SDMMC_RCA(drive), MCI_RESP, &status)) return -5; /* Check TRAN state */ if(wait_for_state(drive, MMC_TRAN)) return -6; /* Switch to 8-bit bus */ if(!send_cmd(drive, MMC_SWITCH, 0x3b70200, MCI_RESP|MCI_BUSY, &status)) return -8; /* switch error ? */ if(status & 0x80) return -9; imx233_ssp_set_bus_width(ssp, 8); /* Switch to high speed mode */ if(!send_cmd(drive, MMC_SWITCH, 0x3b90100, MCI_RESP|MCI_BUSY, &status)) return -10; /* switch error ?*/ if(status & 0x80) return -11; /* SSPCLK @ 96MHz * gives bitrate of 96 / 2 / 1 = 48MHz */ imx233_ssp_set_timings(ssp, 2, 0, 0xffff); /* read extended CSD */ { uint8_t ext_csd[512]; if(imx233_ssp_sd_mmc_transfer(ssp, 8, 0, SSP_SHORT_RESP, aligned_buffer[drive], 1, true, true, &status)) return -12; memcpy(ext_csd, aligned_buffer[drive], 512); uint32_t *sec_count = (void *)&ext_csd[212]; window_start[drive] = 0; window_end[drive] = *sec_count; } /* deselect card */ if(!send_cmd(drive, MMC_DESELECT_CARD, 0, MCI_NO_RESP, NULL)) return -13; return 0; } #endif // low-level function, don't call directly! static int __xfer_sectors(int drive, unsigned long start, int count, void *buf, bool read) { uint32_t resp; int ret = 0; while(count != 0) { int this_count = MIN(count, IMX233_MAX_SINGLE_DMA_XFER_SIZE / 512); /* Set bank_start to the correct unit (blocks or bytes). * MMC drives use block addressing, SD cards bytes or blocks */ int bank_start = start; if(SDMMC_MODE(drive) == SD_MODE && !(SDMMC_INFO(drive).ocr & (1<<30))) /* not SDHC */ bank_start *= SD_BLOCK_SIZE; /* issue read/write * NOTE: rely on SD_{READ,WRITE}_MULTIPLE_BLOCK=MMC_{READ,WRITE}_MULTIPLE_BLOCK */ ret = imx233_ssp_sd_mmc_transfer(SDMMC_SSP(drive), read ? SD_READ_MULTIPLE_BLOCK : SD_WRITE_MULTIPLE_BLOCK, bank_start, SSP_SHORT_RESP, buf, this_count, false, read, &resp); if(ret != SSP_SUCCESS) break; /* stop transmission * NOTE: rely on SD_STOP_TRANSMISSION=MMC_STOP_TRANSMISSION */ if(!send_cmd(drive, SD_STOP_TRANSMISSION, 0, MCI_RESP|MCI_BUSY, &resp)) { ret = -15; break; } count -= this_count; start += this_count; buf += this_count * 512; } return ret; } static int transfer_sectors(int drive, unsigned long start, int count, void *buf, bool read) { int ret = 0; /* update disk activity */ disk_last_activity[drive] = current_tick; /* lock per-drive mutex */ mutex_lock(&mutex[drive]); /* for SD cards, init if necessary */ #if CONFIG_STORAGE & STORAGE_SD if(SDMMC_MODE(drive) == SD_MODE && SDMMC_INFO(drive).initialized <= 0) { ret = init_sd_card(drive); if(SDMMC_INFO(drive).initialized <= 0) goto Lend; } #endif /* check window */ start += window_start[drive]; if((start + count) > window_end[drive]) { ret = -201; goto Lend; } /* select card. * NOTE: rely on SD_SELECT_CARD=MMC_SELECT_CARD */ if(!send_cmd(drive, SD_SELECT_CARD, SDMMC_RCA(drive), MCI_NO_RESP, NULL)) { ret = -20; goto Lend; } /* wait for TRAN state */ /* NOTE: rely on SD_TRAN=MMC_TRAN */ ret = wait_for_state(drive, SD_TRAN); if(ret < 0) goto Ldeselect; /** * NOTE: we need to make sure dma transfers are aligned. This handled * differently for read and write transfers. We do not repeat it each * time but it should be noted that all transfers are limited by * IMX233_MAX_SINGLE_DMA_XFER_SIZE and thus need to be split if needed. * * Read transfers: * If the buffer is already aligned, transfer everything at once. * Otherwise, transfer all sectors but one to the sub-buffer starting * on the next cache ligned and then move the data. Then transfer the * last sector to the aligned_buffer and then copy to the buffer. * * Write transfers: * If the buffer is already aligned, transfer everything at once. * Otherwise, copy the first sector to the aligned_buffer and transfer. * Then move all other sectors within the buffer to make it cache * aligned and transfer it. */ if(read) { void *ptr = CACHEALIGN_UP(buf); if(buf != ptr) { // copy count-1 sector and then move within the buffer ret = __xfer_sectors(drive, start, count - 1, ptr, read); memmove(buf, ptr, 512 * (count - 1)); if(ret >= 0) { // transfer the last sector the aligned_buffer and copy ret = __xfer_sectors(drive, start + count - 1, 1, aligned_buffer[drive], read); memcpy(buf + 512 * (count - 1), aligned_buffer[drive], 512); } } else ret = __xfer_sectors(drive, start, count, buf, read); } else { void *ptr = CACHEALIGN_UP(buf); if(buf != ptr) { // transfer the first sector to aligned_buffer and copy memcpy(aligned_buffer[drive], buf, 512); ret = __xfer_sectors(drive, start, 1, aligned_buffer[drive], read); if(ret >= 0) { // move within the buffer and transfer memmove(ptr, buf + 512, 512 * (count - 1)); ret = __xfer_sectors(drive, start + 1, count - 1, ptr, read); } } else ret = __xfer_sectors(drive, start, count, buf, read); } /* deselect card */ Ldeselect: /* CMD7 w/rca =0 : deselects card & puts it in STBY state * NOTE: rely on SD_DESELECT_CARD=MMC_DESELECT_CARD */ if(!send_cmd(drive, SD_DESELECT_CARD, 0, MCI_NO_RESP, NULL)) ret = -23; Lend: /* release per-drive mutex */ mutex_unlock(&mutex[drive]); return ret; } static int init_drive(int drive) { int ret; switch(SDMMC_MODE(drive)) { #if CONFIG_STORAGE & STORAGE_SD case SD_MODE: ret = init_sd_card(drive); break; #endif #if CONFIG_STORAGE & STORAGE_MMC case MMC_MODE: ret = init_mmc_drive(drive); break; #endif default: ret = 0; } if(ret < 0) return ret; /* compute window */ if((SDMMC_FLAGS(drive) & WINDOW) && imx233_partitions_is_window_enabled()) { uint8_t mbr[512]; int ret = transfer_sectors(drive, 0, 1, mbr, true); if(ret) panicf("Cannot read MBR: %d", ret); ret = imx233_partitions_compute_window(mbr, &window_start[drive], &window_end[drive]); if(ret) panicf("cannot compute partitions window: %d", ret); SDMMC_INFO(drive).numblocks = window_end[drive] - window_start[drive]; } return 0; } static void sdmmc_thread(void) NORETURN_ATTR; static void sdmmc_thread(void) { struct queue_event ev; bool idle_notified = false; int timeout = 0; while (1) { queue_wait_w_tmo(&sdmmc_queue, &ev, HZ); switch(ev.id) { #if CONFIG_STORAGE & STORAGE_SD case SYS_HOTSWAP_INSERTED: case SYS_HOTSWAP_EXTRACTED: { int microsd_init = 1; /* lock-out FAT activity first - * prevent deadlocking via disk_mount that * would cause a reverse-order attempt with * another thread */ fat_lock(); /* We now have exclusive control of fat cache and sd. * Release "by force", ensure file * descriptors aren't leaked and any busy * ones are invalid if mounting. */ for(unsigned sd_drive = 0; sd_drive < _sd_num_drives; sd_drive++) { int drive = sd_map[sd_drive]; /* Skip non-removable drivers */ if(!sd_removable(sd_drive)) continue; /* lock-out card activity - direct calls * into driver that bypass the fat cache */ mutex_lock(&mutex[drive]); disk_unmount(sd_first_drive + sd_drive); /* Force card init for new card, re-init for re-inserted one or * clear if the last attempt to init failed with an error. */ SDMMC_INFO(sd_map[sd_drive]).initialized = 0; if(ev.id == SYS_HOTSWAP_INSERTED) { microsd_init = init_drive(drive); if(microsd_init < 0) /* initialisation failed */ panicf("%s init failed : %d", SDMMC_CONF(sd_map[sd_drive]).name, microsd_init); microsd_init = disk_mount(sd_first_drive + sd_drive); /* 0 if fail */ } /* * Mount succeeded, or this was an EXTRACTED event, * in both cases notify the system about the changed filesystems */ if(microsd_init) queue_broadcast(SYS_FS_CHANGED, 0); /* unlock card */ mutex_unlock(&mutex[drive]); } /* Access is now safe */ fat_unlock(); break; } #endif case SYS_TIMEOUT: #if CONFIG_STORAGE & STORAGE_SD timeout = MAX(timeout, sd_last_disk_activity()+(3*HZ)); #endif #if CONFIG_STORAGE & STORAGE_MMC timeout = MAX(timeout, mmc_last_disk_activity()+(3*HZ)); #endif if(TIME_BEFORE(current_tick, timeout)) { idle_notified = false; } else { next_yield = current_tick; if(!idle_notified) { call_storage_idle_notifys(false); idle_notified = true; } } break; break; case SYS_USB_CONNECTED: usb_acknowledge(SYS_USB_CONNECTED_ACK); /* Wait until the USB cable is extracted again */ usb_wait_for_disconnect(&sdmmc_queue); break; } } } static int sdmmc_init(void) { static int is_initialized = false; if(is_initialized) return 0; is_initialized = true; for(unsigned drive = 0; drive < SDMMC_NUM_DRIVES; drive++) mutex_init(&mutex[drive]); queue_init(&sdmmc_queue, true); create_thread(sdmmc_thread, sdmmc_stack, sizeof(sdmmc_stack), 0, sdmmc_thread_name IF_PRIO(, PRIORITY_USER_INTERFACE) IF_COP(, CPU)); for(unsigned drive = 0; drive < SDMMC_NUM_DRIVES; drive++) { if(SDMMC_FLAGS(drive) & REMOVABLE) imx233_ssp_sdmmc_setup_detect(SDMMC_SSP(drive), true, sdmmc_detect_callback, false, SDMMC_FLAGS(drive) & DETECT_INVERTED); } return 0; } static int sdmmc_present(int drive) { if(SDMMC_FLAGS(drive) & REMOVABLE) return imx233_ssp_sdmmc_detect(SDMMC_SSP(drive)); else return true; } static inline int sdmmc_removable(int drive) { return SDMMC_FLAGS(drive) & REMOVABLE; } #if CONFIG_STORAGE & STORAGE_SD int sd_init(void) { int ret = sdmmc_init(); if(ret < 0) return ret; _sd_num_drives = 0; for(unsigned drive = 0; drive < SDMMC_NUM_DRIVES; drive++) if(SDMMC_MODE(drive) == SD_MODE) sd_map[_sd_num_drives++] = drive; return 0; } tCardInfo *card_get_info_target(int sd_card_no) { return &SDMMC_INFO(sd_map[sd_card_no]); } int sd_num_drives(int first_drive) { sd_first_drive = first_drive; return _sd_num_drives; } bool sd_present(IF_MV_NONVOID(int sd_drive)) { return sdmmc_present(sd_map[sd_drive]); } bool sd_removable(IF_MV_NONVOID(int sd_drive)) { return sdmmc_removable(sd_map[sd_drive]); } long sd_last_disk_activity(void) { long last = 0; for(unsigned i = 0; i < _sd_num_drives; i++) last = MAX(last, disk_last_activity[sd_map[i]]); return last; } void sd_enable(bool on) { (void) on; } int sd_read_sectors(IF_MD2(int sd_drive,) unsigned long start, int count, void *buf) { return transfer_sectors(sd_map[sd_drive], start, count, buf, true); } int sd_write_sectors(IF_MD2(int sd_drive,) unsigned long start, int count, const void* buf) { return transfer_sectors(sd_map[sd_drive], start, count, (void *)buf, false); } #endif #if CONFIG_STORAGE & STORAGE_MMC int mmc_init(void) { int ret = sdmmc_init(); if(ret < 0) return ret; _sd_num_drives = 0; for(unsigned drive = 0; drive < SDMMC_NUM_DRIVES; drive++) if(SDMMC_MODE(drive) == MMC_MODE) { mmc_map[_mmc_num_drives++] = drive; init_drive(drive); } return 0; } void mmc_get_info(IF_MD2(int mmc_drive,) struct storage_info *info) { int drive = mmc_map[mmc_drive]; info->sector_size = 512; info->num_sectors = window_end[drive] - window_start[drive]; info->vendor = "Rockbox"; info->product = "Internal Storage"; info->revision = "0.00"; } int mmc_num_drives(int first_drive) { mmc_first_drive = first_drive; return _mmc_num_drives; } bool mmc_present(IF_MV_NONVOID(int mmc_drive)) { return sdmmc_present(mmc_map[mmc_drive]); } bool mmc_removable(IF_MV_NONVOID(int mmc_drive)) { return sdmmc_removable(mmc_map[mmc_drive]); } long mmc_last_disk_activity(void) { long last = 0; for(unsigned i = 0; i < _mmc_num_drives; i++) last = MAX(last, disk_last_activity[mmc_map[i]]); return last; } void mmc_enable(bool on) { (void) on; } void mmc_sleep(void) { } void mmc_sleepnow(void) { } bool mmc_disk_is_active(void) { return false; } bool mmc_usb_active(void) { return mmc_disk_is_active(); } int mmc_soft_reset(void) { return 0; } int mmc_flush(void) { return 0; } void mmc_spin(void) { } void mmc_spindown(int seconds) { (void) seconds; } int mmc_spinup_time(void) { return 0; } int mmc_read_sectors(IF_MD2(int mmc_drive,) unsigned long start, int count, void *buf) { return transfer_sectors(mmc_map[mmc_drive], start, count, buf, true); } int mmc_write_sectors(IF_MD2(int mmc_drive,) unsigned long start, int count, const void* buf) { return transfer_sectors(mmc_map[mmc_drive], start, count, (void *)buf, false); } #endif