/*************************************************************************** * __________ __ ___. * Open \______ \ ____ ____ | | _\_ |__ _______ ___ * Source | _// _ \_/ ___\| |/ /| __ \ / _ \ \/ / * Jukebox | | ( <_> ) \___| < | \_\ ( <_> > < < * Firmware |____|_ /\____/ \___ >__|_ \|___ /\____/__/\_ \ * \/ \/ \/ \/ \/ * $Id$ * * Copyright (C) 2008 by Maurus Cuelenaere * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License * as published by the Free Software Foundation; either version 2 * of the License, or (at your option) any later version. * * This software is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY * KIND, either express or implied. * ****************************************************************************/ #include "config.h" #include "jz4740.h" #include "ata.h" #include "ata-sd-target.h" #include "sd.h" #include "system.h" #include "kernel.h" #include "panic.h" #include "debug.h" static struct wakeup sd_wakeup; //#define MMC_DMA_ENABLE #define MMC_DMA_INTERRUPT 0 //#define DEBUG(x...) DEBUGF(x); #define DEBUG(x...) printf(x); #ifdef MMC_POWER_PIN #define MMC_POWER_OFF() \ do { \ __gpio_set_pin(MMC_POWER_PIN); \ } while (0) #define MMC_POWER_ON() \ do { \ __gpio_clear_pin(MMC_POWER_PIN); \ } while (0) #endif #ifdef MMC_CD_PIN #define MMC_INSERT_STATUS() __gpio_get_pin(MMC_CD_PIN) #endif #define MMC_RESET() __msc_reset() #define MMC_IRQ_MASK() \ do { \ REG_MSC_IMASK = 0xffff; \ REG_MSC_IREG = 0xffff; \ } while (0) /* Error codes */ enum mmc_result_t { MMC_NO_RESPONSE = -1, MMC_NO_ERROR = 0, MMC_ERROR_OUT_OF_RANGE, MMC_ERROR_ADDRESS, MMC_ERROR_BLOCK_LEN, MMC_ERROR_ERASE_SEQ, MMC_ERROR_ERASE_PARAM, MMC_ERROR_WP_VIOLATION, MMC_ERROR_CARD_IS_LOCKED, MMC_ERROR_LOCK_UNLOCK_FAILED, MMC_ERROR_COM_CRC, MMC_ERROR_ILLEGAL_COMMAND, MMC_ERROR_CARD_ECC_FAILED, MMC_ERROR_CC, MMC_ERROR_GENERAL, MMC_ERROR_UNDERRUN, MMC_ERROR_OVERRUN, MMC_ERROR_CID_CSD_OVERWRITE, MMC_ERROR_STATE_MISMATCH, MMC_ERROR_HEADER_MISMATCH, MMC_ERROR_TIMEOUT, MMC_ERROR_CRC, MMC_ERROR_DRIVER_FAILURE, }; /* Standard MMC/SD clock speeds */ #define MMC_CLOCK_SLOW 400000 /* 400 kHz for initial setup */ #define MMC_CLOCK_FAST 20000000 /* 20 MHz for maximum for normal operation */ #define SD_CLOCK_FAST 24000000 /* 24 MHz for SD Cards */ #define SD_CLOCK_HIGH 48000000 /* 48 MHz for SD Cards */ /* Extra MMC commands for state control */ /* Use negative numbers to disambiguate */ #define MMC_CIM_RESET -1 /* Standard MMC commands (3.1) type argument response */ /* class 1 */ #define MMC_GO_IDLE_STATE 0 /* bc */ #define MMC_SEND_OP_COND 1 /* bcr [31:0] OCR R3 */ #define MMC_ALL_SEND_CID 2 /* bcr R2 */ #define MMC_SET_RELATIVE_ADDR 3 /* ac [31:16] RCA R1 */ #define MMC_SET_DSR 4 /* bc [31:16] RCA */ #define MMC_SELECT_CARD 7 /* ac [31:16] RCA R1 */ #define MMC_SEND_CSD 9 /* ac [31:16] RCA R2 */ #define MMC_SEND_CID 10 /* ac [31:16] RCA R2 */ #define MMC_READ_DAT_UNTIL_STOP 11 /* adtc [31:0] dadr R1 */ #define MMC_STOP_TRANSMISSION 12 /* ac R1b */ #define MMC_SEND_STATUS 13 /* ac [31:16] RCA R1 */ #define MMC_GO_INACTIVE_STATE 15 /* ac [31:16] RCA */ /* class 2 */ #define MMC_SET_BLOCKLEN 16 /* ac [31:0] block len R1 */ #define MMC_READ_SINGLE_BLOCK 17 /* adtc [31:0] data addr R1 */ #define MMC_READ_MULTIPLE_BLOCK 18 /* adtc [31:0] data addr R1 */ /* class 3 */ #define MMC_WRITE_DAT_UNTIL_STOP 20 /* adtc [31:0] data addr R1 */ /* class 4 */ #define MMC_SET_BLOCK_COUNT 23 /* adtc [31:0] data addr R1 */ #define MMC_WRITE_BLOCK 24 /* adtc [31:0] data addr R1 */ #define MMC_WRITE_MULTIPLE_BLOCK 25 /* adtc R1 */ #define MMC_PROGRAM_CID 26 /* adtc R1 */ #define MMC_PROGRAM_CSD 27 /* adtc R1 */ /* class 6 */ #define MMC_SET_WRITE_PROT 28 /* ac [31:0] data addr R1b */ #define MMC_CLR_WRITE_PROT 29 /* ac [31:0] data addr R1b */ #define MMC_SEND_WRITE_PROT 30 /* adtc [31:0] wpdata addr R1 */ /* class 5 */ #define MMC_ERASE_GROUP_START 35 /* ac [31:0] data addr R1 */ #define MMC_ERASE_GROUP_END 36 /* ac [31:0] data addr R1 */ #define MMC_ERASE 37 /* ac R1b */ /* class 9 */ #define MMC_FAST_IO 39 /* ac R4 */ #define MMC_GO_IRQ_STATE 40 /* bcr R5 */ /* class 7 */ #define MMC_LOCK_UNLOCK 42 /* adtc R1b */ /* class 8 */ #define MMC_APP_CMD 55 /* ac [31:16] RCA R1 */ #define MMC_GEN_CMD 56 /* adtc [0] RD/WR R1b */ /* SD class */ #define SD_SEND_OP_COND 41 /* bcr [31:0] OCR R3 */ #define SET_BUS_WIDTH 6 /* ac [1:0] bus width R1 */ #define SEND_SCR 51 /* adtc [31:0] staff R1 */ /* Don't change the order of these; they are used in dispatch tables */ enum mmc_rsp_t { RESPONSE_NONE = 0, RESPONSE_R1 = 1, RESPONSE_R1B = 2, RESPONSE_R2_CID = 3, RESPONSE_R2_CSD = 4, RESPONSE_R3 = 5, RESPONSE_R4 = 6, RESPONSE_R5 = 7, RESPONSE_R6 = 8, }; /* MMC status in R1 Type e : error bit s : status bit r : detected and set for the actual command response x : detected and set during command execution. the host must poll the card by sending status command in order to read these bits. Clear condition a : according to the card state b : always related to the previous command. Reception of a valid command will clear it (with a delay of one command) c : clear by read */ #define R1_OUT_OF_RANGE (1 << 31) /* er, c */ #define R1_ADDRESS_ERROR (1 << 30) /* erx, c */ #define R1_BLOCK_LEN_ERROR (1 << 29) /* er, c */ #define R1_ERASE_SEQ_ERROR (1 << 28) /* er, c */ #define R1_ERASE_PARAM (1 << 27) /* ex, c */ #define R1_WP_VIOLATION (1 << 26) /* erx, c */ #define R1_CARD_IS_LOCKED (1 << 25) /* sx, a */ #define R1_LOCK_UNLOCK_FAILED (1 << 24) /* erx, c */ #define R1_COM_CRC_ERROR (1 << 23) /* er, b */ #define R1_ILLEGAL_COMMAND (1 << 22) /* er, b */ #define R1_CARD_ECC_FAILED (1 << 21) /* ex, c */ #define R1_CC_ERROR (1 << 20) /* erx, c */ #define R1_ERROR (1 << 19) /* erx, c */ #define R1_UNDERRUN (1 << 18) /* ex, c */ #define R1_OVERRUN (1 << 17) /* ex, c */ #define R1_CID_CSD_OVERWRITE (1 << 16) /* erx, c, CID/CSD overwrite */ #define R1_WP_ERASE_SKIP (1 << 15) /* sx, c */ #define R1_CARD_ECC_DISABLED (1 << 14) /* sx, a */ #define R1_ERASE_RESET (1 << 13) /* sr, c */ #define R1_STATUS(x) (x & 0xFFFFE000) #define R1_CURRENT_STATE(x) ((x & 0x00001E00) >> 9) /* sx, b (4 bits) */ #define R1_READY_FOR_DATA (1 << 8) /* sx, a */ #define R1_APP_CMD (1 << 7) /* sr, c */ enum card_state { CARD_STATE_EMPTY = -1, CARD_STATE_IDLE = 0, CARD_STATE_READY = 1, CARD_STATE_IDENT = 2, CARD_STATE_STBY = 3, CARD_STATE_TRAN = 4, CARD_STATE_DATA = 5, CARD_STATE_RCV = 6, CARD_STATE_PRG = 7, CARD_STATE_DIS = 8, }; /* These are unpacked versions of the actual responses */ struct mmc_response_r1 { unsigned char cmd; unsigned int status; }; struct mmc_cid { unsigned char mid; unsigned short oid; unsigned char pnm[7]; /* Product name (we null-terminate) */ unsigned char prv; unsigned int psn; unsigned char mdt; }; struct mmc_csd { unsigned char csd_structure; unsigned char spec_vers; unsigned char taac; unsigned char nsac; unsigned char tran_speed; unsigned short ccc; unsigned char read_bl_len; unsigned char read_bl_partial; unsigned char write_blk_misalign; unsigned char read_blk_misalign; unsigned char dsr_imp; unsigned short c_size; unsigned char vdd_r_curr_min; unsigned char vdd_r_curr_max; unsigned char vdd_w_curr_min; unsigned char vdd_w_curr_max; unsigned char c_size_mult; union { struct /* MMC system specification version 3.1 */ { unsigned char erase_grp_size; unsigned char erase_grp_mult; } v31; struct /* MMC system specification version 2.2 */ { unsigned char sector_size; unsigned char erase_grp_size; } v22; } erase; unsigned char wp_grp_size; unsigned char wp_grp_enable; unsigned char default_ecc; unsigned char r2w_factor; unsigned char write_bl_len; unsigned char write_bl_partial; unsigned char file_format_grp; unsigned char copy; unsigned char perm_write_protect; unsigned char tmp_write_protect; unsigned char file_format; unsigned char ecc; }; struct mmc_response_r3 { unsigned int ocr; }; #define MMC_VDD_145_150 0x00000001 /* VDD voltage 1.45 - 1.50 */ #define MMC_VDD_150_155 0x00000002 /* VDD voltage 1.50 - 1.55 */ #define MMC_VDD_155_160 0x00000004 /* VDD voltage 1.55 - 1.60 */ #define MMC_VDD_160_165 0x00000008 /* VDD voltage 1.60 - 1.65 */ #define MMC_VDD_165_170 0x00000010 /* VDD voltage 1.65 - 1.70 */ #define MMC_VDD_17_18 0x00000020 /* VDD voltage 1.7 - 1.8 */ #define MMC_VDD_18_19 0x00000040 /* VDD voltage 1.8 - 1.9 */ #define MMC_VDD_19_20 0x00000080 /* VDD voltage 1.9 - 2.0 */ #define MMC_VDD_20_21 0x00000100 /* VDD voltage 2.0 ~ 2.1 */ #define MMC_VDD_21_22 0x00000200 /* VDD voltage 2.1 ~ 2.2 */ #define MMC_VDD_22_23 0x00000400 /* VDD voltage 2.2 ~ 2.3 */ #define MMC_VDD_23_24 0x00000800 /* VDD voltage 2.3 ~ 2.4 */ #define MMC_VDD_24_25 0x00001000 /* VDD voltage 2.4 ~ 2.5 */ #define MMC_VDD_25_26 0x00002000 /* VDD voltage 2.5 ~ 2.6 */ #define MMC_VDD_26_27 0x00004000 /* VDD voltage 2.6 ~ 2.7 */ #define MMC_VDD_27_28 0x00008000 /* VDD voltage 2.7 ~ 2.8 */ #define MMC_VDD_28_29 0x00010000 /* VDD voltage 2.8 ~ 2.9 */ #define MMC_VDD_29_30 0x00020000 /* VDD voltage 2.9 ~ 3.0 */ #define MMC_VDD_30_31 0x00040000 /* VDD voltage 3.0 ~ 3.1 */ #define MMC_VDD_31_32 0x00080000 /* VDD voltage 3.1 ~ 3.2 */ #define MMC_VDD_32_33 0x00100000 /* VDD voltage 3.2 ~ 3.3 */ #define MMC_VDD_33_34 0x00200000 /* VDD voltage 3.3 ~ 3.4 */ #define MMC_VDD_34_35 0x00400000 /* VDD voltage 3.4 ~ 3.5 */ #define MMC_VDD_35_36 0x00800000 /* VDD voltage 3.5 ~ 3.6 */ #define MMC_CARD_BUSY 0x80000000 /* Card Power up status bit */ /* CSD field definitions */ #define CSD_STRUCT_VER_1_0 0 /* Valid for system specification 1.0 - 1.2 */ #define CSD_STRUCT_VER_1_1 1 /* Valid for system specification 1.4 - 2.2 */ #define CSD_STRUCT_VER_1_2 2 /* Valid for system specification 3.1 */ #define CSD_SPEC_VER_0 0 /* Implements system specification 1.0 - 1.2 */ #define CSD_SPEC_VER_1 1 /* Implements system specification 1.4 */ #define CSD_SPEC_VER_2 2 /* Implements system specification 2.0 - 2.2 */ #define CSD_SPEC_VER_3 3 /* Implements system specification 3.1 */ /* the information structure of MMC/SD Card */ typedef struct MMC_INFO { int id; /* Card index */ int sd; /* MMC or SD card */ int rca; /* RCA */ unsigned int scr; /* SCR 63:32*/ int flags; /* Ejected, inserted */ enum card_state state; /* empty, ident, ready, whatever */ /* Card specific information */ struct mmc_cid cid; struct mmc_csd csd; unsigned int block_num; unsigned int block_len; unsigned int erase_unit; } mmc_info; static mmc_info mmcinfo; struct mmc_request { int index; /* Slot index - used for CS lines */ int cmd; /* Command to send */ unsigned int arg; /* Argument to send */ enum mmc_rsp_t rtype; /* Response type expected */ /* Data transfer (these may be modified at the low level) */ unsigned short nob; /* Number of blocks to transfer*/ unsigned short block_len; /* Block length */ unsigned char *buffer; /* Data buffer */ unsigned int cnt; /* Data length, for PIO */ /* Results */ unsigned char response[18]; /* Buffer to store response - CRC is optional */ enum mmc_result_t result; }; #define MMC_OCR_ARG 0x00ff8000 /* Argument of OCR */ /*********************************************************************** * MMC Events */ #define MMC_EVENT_NONE 0x00 /* No events */ #define MMC_EVENT_RX_DATA_DONE 0x01 /* Rx data done */ #define MMC_EVENT_TX_DATA_DONE 0x02 /* Tx data done */ #define MMC_EVENT_PROG_DONE 0x04 /* Programming is done */ static int use_4bit; /* Use 4-bit data bus */ static int num_6; static int sd2_0; /* Stop the MMC clock and wait while it happens */ static inline int jz_mmc_stop_clock(void) { int timeout = 1000; DEBUG("stop MMC clock"); REG_MSC_STRPCL = MSC_STRPCL_CLOCK_CONTROL_STOP; while (timeout && (REG_MSC_STAT & MSC_STAT_CLK_EN)) { timeout--; if (timeout == 0) { DEBUG("Timeout on stop clock waiting"); return MMC_ERROR_TIMEOUT; } udelay(1); } DEBUG("clock off time is %d microsec", timeout); return MMC_NO_ERROR; } /* Start the MMC clock and operation */ static inline int jz_mmc_start_clock(void) { REG_MSC_STRPCL = MSC_STRPCL_CLOCK_CONTROL_START | MSC_STRPCL_START_OP; return MMC_NO_ERROR; } static inline unsigned int jz_mmc_calc_clkrt(int is_sd, unsigned int rate) { unsigned int clkrt; unsigned int clk_src = is_sd ? 24000000 : 20000000; clkrt = 0; while (rate < clk_src) { clkrt++; clk_src >>= 1; } return clkrt; } static int jz_mmc_check_status(struct mmc_request *request) { unsigned int status = REG_MSC_STAT; /* Checking for response or data timeout */ if (status & (MSC_STAT_TIME_OUT_RES | MSC_STAT_TIME_OUT_READ)) { DEBUG("MMC/SD timeout, MMC_STAT 0x%x CMD %d", status, request->cmd); return MMC_ERROR_TIMEOUT; } /* Checking for CRC error */ if (status & (MSC_STAT_CRC_READ_ERROR | MSC_STAT_CRC_WRITE_ERROR | MSC_STAT_CRC_RES_ERR)) { DEBUG("MMC/CD CRC error, MMC_STAT 0x%x", status); return MMC_ERROR_CRC; } return MMC_NO_ERROR; } /* Obtain response to the command and store it to response buffer */ static void jz_mmc_get_response(struct mmc_request *request) { int i; unsigned char *buf; unsigned int data; DEBUG("fetch response for request %d, cmd %d", request->rtype, request->cmd); buf = request->response; request->result = MMC_NO_ERROR; switch (request->rtype) { case RESPONSE_R1: case RESPONSE_R1B: case RESPONSE_R6: case RESPONSE_R3: case RESPONSE_R4: case RESPONSE_R5: { data = REG_MSC_RES; buf[0] = (data >> 8) & 0xff; buf[1] = data & 0xff; data = REG_MSC_RES; buf[2] = (data >> 8) & 0xff; buf[3] = data & 0xff; data = REG_MSC_RES; buf[4] = data & 0xff; DEBUG("request %d, response [%02x %02x %02x %02x %02x]", request->rtype, buf[0], buf[1], buf[2], buf[3], buf[4]); break; } case RESPONSE_R2_CID: case RESPONSE_R2_CSD: { for (i = 0; i < 16; i += 2) { data = REG_MSC_RES; buf[i] = (data >> 8) & 0xff; buf[i + 1] = data & 0xff; } DEBUG("request %d, response []", request->rtype); break; } case RESPONSE_NONE: DEBUG("No response"); break; default: DEBUG("unhandled response type for request %d", request->rtype); break; } } #ifdef MMC_DMA_ENABLE static int jz_mmc_receive_data_dma(struct mmc_request *req) { int ch = RX_DMA_CHANNEL; unsigned int size = req->block_len * req->nob; unsigned char err = 0; /* flush dcache */ dma_cache_wback_inv((unsigned long) req->buffer, size); /* setup dma channel */ REG_DMAC_DSAR(ch) = PHYSADDR(MSC_RXFIFO); /* DMA source addr */ REG_DMAC_DTAR(ch) = PHYSADDR((unsigned long) req->buffer); /* DMA dest addr */ REG_DMAC_DTCR(ch) = (size + 3) / 4; /* DMA transfer count */ REG_DMAC_DRSR(ch) = DMAC_DRSR_RS_MSCIN; /* DMA request type */ #if MMC_DMA_INTERRUPT REG_DMAC_DCMD(ch) = DMAC_DCMD_DAI | DMAC_DCMD_SWDH_32 | DMAC_DCMD_DWDH_32 | DMAC_DCMD_DS_32BIT | DMAC_DCMD_TIE; REG_DMAC_DCCSR(ch) = DMAC_DCCSR_EN | DMAC_DCCSR_NDES; OSSemPend(mmc_dma_rx_sem, 100, &err); #else REG_DMAC_DCMD(ch) = DMAC_DCMD_DAI | DMAC_DCMD_SWDH_32 | DMAC_DCMD_DWDH_32 | DMAC_DCMD_DS_32BIT; REG_DMAC_DCCSR(ch) = DMAC_DCCSR_EN | DMAC_DCCSR_NDES; while (REG_DMAC_DTCR(ch)); #endif /* clear status and disable channel */ REG_DMAC_DCCSR(ch) = 0; #if MMC_DMA_INTERRUPT return (err == OS_NO_ERR); #else return 0; #endif } static int jz_mmc_transmit_data_dma(struct mmc_request *req) { int ch = TX_DMA_CHANNEL; unsigned int size = req->block_len * req->nob; unsigned char err = 0; /* flush dcache */ dma_cache_wback_inv((unsigned long) req->buffer, size); /* setup dma channel */ REG_DMAC_DSAR(ch) = PHYSADDR((unsigned long) req->buffer); /* DMA source addr */ REG_DMAC_DTAR(ch) = PHYSADDR(MSC_TXFIFO); /* DMA dest addr */ REG_DMAC_DTCR(ch) = (size + 3) / 4; /* DMA transfer count */ REG_DMAC_DRSR(ch) = DMAC_DRSR_RS_MSCOUT; /* DMA request type */ #if MMC_DMA_INTERRUPT REG_DMAC_DCMD(ch) = DMAC_DCMD_SAI | DMAC_DCMD_SWDH_32 | DMAC_DCMD_DWDH_32 | DMAC_DCMD_DS_32BIT | DMAC_DCMD_TIE; REG_DMAC_DCCSR(ch) = DMAC_DCCSR_EN | DMAC_DCCSR_NDES; OSSemPend(mmc_dma_tx_sem, 100, &err); #else REG_DMAC_DCMD(ch) = DMAC_DCMD_SAI | DMAC_DCMD_SWDH_32 | DMAC_DCMD_DWDH_32 | DMAC_DCMD_DS_32BIT; REG_DMAC_DCCSR(ch) = DMAC_DCCSR_EN | DMAC_DCCSR_NDES; /* wait for dma completion */ while (REG_DMAC_DTCR(ch)); #endif /* clear status and disable channel */ REG_DMAC_DCCSR(ch) = 0; #if MMC_DMA_INTERRUPT return (err == OS_NO_ERR); #else return 0; #endif } #endif /* MMC_DMA_ENABLE */ static int jz_mmc_receive_data(struct mmc_request *req) { unsigned int nob = req->nob; unsigned int wblocklen = (unsigned int) (req->block_len + 3) >> 2; /* length in word */ unsigned char *buf = req->buffer; unsigned int *wbuf = (unsigned int *) buf; unsigned int waligned = (((unsigned int) buf & 0x3) == 0); /* word aligned ? */ unsigned int stat, timeout, data, cnt; for (; nob >= 1; nob--) { timeout = 0x3FFFFFF; while (timeout) { timeout--; stat = REG_MSC_STAT; if (stat & MSC_STAT_TIME_OUT_READ) return MMC_ERROR_TIMEOUT; else if (stat & MSC_STAT_CRC_READ_ERROR) return MMC_ERROR_CRC; else if (!(stat & MSC_STAT_DATA_FIFO_EMPTY) || (stat & MSC_STAT_DATA_FIFO_AFULL)) { /* Ready to read data */ break; } udelay(1); } if (!timeout) return MMC_ERROR_TIMEOUT; /* Read data from RXFIFO. It could be FULL or PARTIAL FULL */ DEBUG("Receive Data = %d", wblocklen); cnt = wblocklen; while (cnt) { data = REG_MSC_RXFIFO; if (waligned) *wbuf++ = data; else { *buf++ = (unsigned char) (data >> 0); *buf++ = (unsigned char) (data >> 8); *buf++ = (unsigned char) (data >> 16); *buf++ = (unsigned char) (data >> 24); } cnt--; while (cnt && (REG_MSC_STAT & MSC_STAT_DATA_FIFO_EMPTY)); } } return MMC_NO_ERROR; } static int jz_mmc_transmit_data(struct mmc_request *req) { unsigned int nob = req->nob; unsigned int wblocklen = (unsigned int) (req->block_len + 3) >> 2; /* length in word */ unsigned char *buf = req->buffer; unsigned int *wbuf = (unsigned int *) buf; unsigned int waligned = (((unsigned int) buf & 0x3) == 0); /* word aligned ? */ unsigned int stat, timeout, data, cnt; for (; nob >= 1; nob--) { timeout = 0x3FFFFFF; while (timeout) { timeout--; stat = REG_MSC_STAT; if (stat & (MSC_STAT_CRC_WRITE_ERROR | MSC_STAT_CRC_WRITE_ERROR_NOSTS)) return MMC_ERROR_CRC; else if (!(stat & MSC_STAT_DATA_FIFO_FULL)) { /* Ready to write data */ break; } udelay(1); } if (!timeout) return MMC_ERROR_TIMEOUT; /* Write data to TXFIFO */ cnt = wblocklen; while (cnt) { while (REG_MSC_STAT & MSC_STAT_DATA_FIFO_FULL); if (waligned) REG_MSC_TXFIFO = *wbuf++; else { data = *buf++; data |= *buf++ << 8; data |= *buf++ << 16; data |= *buf++ << 24; REG_MSC_TXFIFO = data; } cnt--; } } return MMC_NO_ERROR; } /* Set the MMC clock frequency */ static void jz_mmc_set_clock(int sd, unsigned int rate) { int clkrt = 0; sd = sd ? 1 : 0; jz_mmc_stop_clock(); if(sd2_0) { __cpm_select_msc_hs_clk(sd); /* select clock source from CPM */ REG_CPM_CPCCR |= CPM_CPCCR_CE; REG_MSC_CLKRT = 0; } else { __cpm_select_msc_clk(sd); /* select clock source from CPM */ REG_CPM_CPCCR |= CPM_CPCCR_CE; clkrt = jz_mmc_calc_clkrt(sd, rate); REG_MSC_CLKRT = clkrt; } DEBUG("set clock to %u Hz is_sd=%d clkrt=%d", rate, sd, clkrt); } /******************************************************************************************************************** ** Name: int jz_mmc_exec_cmd() ** Function: send command to the card, and get a response ** Input: struct mmc_request *req: MMC/SD request ** Output: 0: right >0: error code ********************************************************************************************************************/ static int jz_mmc_exec_cmd(struct mmc_request *request) { unsigned int cmdat = 0, events = 0; int retval, timeout = 0x3fffff; /* Indicate we have no result yet */ request->result = MMC_NO_RESPONSE; if (request->cmd == MMC_CIM_RESET) { /* On reset, 1-bit bus width */ use_4bit = 0; /* Reset MMC/SD controller */ __msc_reset(); /* On reset, drop MMC clock down */ jz_mmc_set_clock(0, MMC_CLOCK_SLOW); /* On reset, stop MMC clock */ jz_mmc_stop_clock(); } #if 0 if (request->cmd == MMC_SEND_OP_COND) { DEBUG("Have a MMC card"); /* always use 1bit for MMC */ use_4bit = 0; } #endif if (request->cmd == SET_BUS_WIDTH) { if (request->arg == 0x2) { DEBUG("Use 4-bit bus width"); use_4bit = 1; } else { DEBUG("Use 1-bit bus width"); use_4bit = 0; } } /* stop clock */ jz_mmc_stop_clock(); /* mask all interrupts */ //REG_MSC_IMASK = 0xffff; /* clear status */ REG_MSC_IREG = 0xffff; /*open interrupt */ REG_MSC_IMASK = (~7); /* use 4-bit bus width when possible */ if (use_4bit) cmdat |= MSC_CMDAT_BUS_WIDTH_4BIT; /* Set command type and events */ switch (request->cmd) { /* MMC core extra command */ case MMC_CIM_RESET: cmdat |= MSC_CMDAT_INIT; /* Initialization sequence sent prior to command */ break; /* bc - broadcast - no response */ case MMC_GO_IDLE_STATE: case MMC_SET_DSR: break; /* bcr - broadcast with response */ case MMC_SEND_OP_COND: case MMC_ALL_SEND_CID: case MMC_GO_IRQ_STATE: break; /* adtc - addressed with data transfer */ case MMC_READ_DAT_UNTIL_STOP: case MMC_READ_SINGLE_BLOCK: case MMC_READ_MULTIPLE_BLOCK: case SEND_SCR: #if defined(MMC_DMA_ENABLE) cmdat |= MSC_CMDAT_DATA_EN | MSC_CMDAT_READ | MSC_CMDAT_DMA_EN; #else cmdat |= MSC_CMDAT_DATA_EN | MSC_CMDAT_READ; #endif events = MMC_EVENT_RX_DATA_DONE; break; case 6: if (num_6 < 2) { #if defined(MMC_DMA_ENABLE) cmdat |= MSC_CMDAT_DATA_EN | MSC_CMDAT_READ | MSC_CMDAT_DMA_EN; #else cmdat |= MSC_CMDAT_DATA_EN | MSC_CMDAT_READ; #endif events = MMC_EVENT_RX_DATA_DONE; } break; case MMC_WRITE_DAT_UNTIL_STOP: case MMC_WRITE_BLOCK: case MMC_WRITE_MULTIPLE_BLOCK: case MMC_PROGRAM_CID: case MMC_PROGRAM_CSD: case MMC_SEND_WRITE_PROT: case MMC_GEN_CMD: case MMC_LOCK_UNLOCK: #if defined(MMC_DMA_ENABLE) cmdat |= MSC_CMDAT_DATA_EN | MSC_CMDAT_WRITE | MSC_CMDAT_DMA_EN; #else cmdat |= MSC_CMDAT_DATA_EN | MSC_CMDAT_WRITE; #endif events = MMC_EVENT_TX_DATA_DONE | MMC_EVENT_PROG_DONE; break; case MMC_STOP_TRANSMISSION: events = MMC_EVENT_PROG_DONE; break; /* ac - no data transfer */ default: break; } /* Set response type */ switch (request->rtype) { case RESPONSE_NONE: break; case RESPONSE_R1B: cmdat |= MSC_CMDAT_BUSY; /*FALLTHRU*/ case RESPONSE_R1: cmdat |= MSC_CMDAT_RESPONSE_R1; break; case RESPONSE_R2_CID: case RESPONSE_R2_CSD: cmdat |= MSC_CMDAT_RESPONSE_R2; break; case RESPONSE_R3: cmdat |= MSC_CMDAT_RESPONSE_R3; break; case RESPONSE_R4: cmdat |= MSC_CMDAT_RESPONSE_R4; break; case RESPONSE_R5: cmdat |= MSC_CMDAT_RESPONSE_R5; break; case RESPONSE_R6: cmdat |= MSC_CMDAT_RESPONSE_R6; break; default: break; } /* Set command index */ if (request->cmd == MMC_CIM_RESET) REG_MSC_CMD = MMC_GO_IDLE_STATE; else REG_MSC_CMD = request->cmd; /* Set argument */ REG_MSC_ARG = request->arg; /* Set block length and nob */ if (request->cmd == SEND_SCR) { /* get SCR from DataFIFO */ REG_MSC_BLKLEN = 8; REG_MSC_NOB = 1; } else { REG_MSC_BLKLEN = request->block_len; REG_MSC_NOB = request->nob; } /* Set command */ REG_MSC_CMDAT = cmdat; DEBUG("Send cmd %d cmdat: %x arg: %x resp %d", request->cmd, cmdat, request->arg, request->rtype); /* Start MMC/SD clock and send command to card */ jz_mmc_start_clock(); /* Wait for command completion */ //__intc_unmask_irq(IRQ_MSC); //wakeup_wait(&sd_wakeup, 100); while (timeout-- && !(REG_MSC_STAT & MSC_STAT_END_CMD_RES)); if (timeout == 0) return MMC_ERROR_TIMEOUT; REG_MSC_IREG = MSC_IREG_END_CMD_RES; /* clear flag */ /* Check for status */ retval = jz_mmc_check_status(request); if (retval) return retval; /* Complete command with no response */ if (request->rtype == RESPONSE_NONE) return MMC_NO_ERROR; /* Get response */ jz_mmc_get_response(request); /* Start data operation */ if (events & (MMC_EVENT_RX_DATA_DONE | MMC_EVENT_TX_DATA_DONE)) { if (events & MMC_EVENT_RX_DATA_DONE) { if (request->cmd == SEND_SCR) { /* SD card returns SCR register as data. MMC core expect it in the response buffer, after normal response. */ request->buffer = (unsigned char *) ((unsigned int) request->response + 5); } #ifdef MMC_DMA_ENABLE jz_mmc_receive_data_dma(request); #else jz_mmc_receive_data(request); #endif } if (events & MMC_EVENT_TX_DATA_DONE) { #ifdef MMC_DMA_ENABLE jz_mmc_transmit_data_dma(request); #else jz_mmc_transmit_data(request); #endif } //__intc_unmask_irq(IRQ_MSC); //wakeup_wait(&sd_wakeup, 100); /* Wait for Data Done */ while (!(REG_MSC_IREG & MSC_IREG_DATA_TRAN_DONE)); REG_MSC_IREG = MSC_IREG_DATA_TRAN_DONE; /* clear status */ } /* Wait for Prog Done event */ if (events & MMC_EVENT_PROG_DONE) { //__intc_unmask_irq(IRQ_MSC); //wakeup_wait(&sd_wakeup, 100); while (!(REG_MSC_IREG & MSC_IREG_PRG_DONE)); REG_MSC_IREG = MSC_IREG_PRG_DONE; /* clear status */ } /* Command completed */ return MMC_NO_ERROR; /* return successfully */ } /******************************************************************************************************************* ** Name: int mmc_chkcard() ** Function: check whether card is insert entirely ** Input: NULL ** Output: 1: insert entirely 0: not insert entirely ********************************************************************************************************************/ static int jz_mmc_chkcard(void) { if (MMC_INSERT_STATUS() == 0) return 1; /* insert entirely */ else return 0; /* not insert entirely */ } #if MMC_DMA_INTERRUPT static void jz_mmc_tx_handler(unsigned int arg) { if (__dmac_channel_address_error_detected(arg)) { DEBUG("%s: DMAC address error.", __FUNCTION__); __dmac_channel_clear_address_error(arg); } if (__dmac_channel_transmit_end_detected(arg)) { __dmac_channel_clear_transmit_end(arg); OSSemPost(mmc_dma_tx_sem); } } static void jz_mmc_rx_handler(unsigned int arg) { if (__dmac_channel_address_error_detected(arg)) { DEBUG("%s: DMAC address error.", __FUNCTION__); __dmac_channel_clear_address_error(arg); } if (__dmac_channel_transmit_end_detected(arg)) { __dmac_channel_clear_transmit_end(arg); OSSemPost(mmc_dma_rx_sem); } } #endif /* MSC interrupt handler */ void MSC(void) { //wakeup_signal(&sd_wakeup); } /******************************************************************************************************************* ** Name: void mmc_hardware_init() ** Function: initialize the hardware condiction that access sd card ** Input: NULL ** Output: NULL ********************************************************************************************************************/ static void jz_mmc_hardware_init(void) { mmc_init_gpio(); /* init GPIO */ #ifdef MMC_POWER_ON MMC_POWER_ON(); /* turn on power of card */ #endif MMC_RESET(); /* reset mmc/sd controller */ MMC_IRQ_MASK(); /* mask all IRQs */ jz_mmc_stop_clock(); /* stop MMC/SD clock */ __cpm_start_msc(); #ifdef MMC_DMA_ENABLE // __cpm_start_dmac(); // __dmac_enable_module(); // REG_DMAC_DMACR = DMAC_DMACR_DME; #if MMC_DMA_INTERRUPT mmc_dma_rx_sem = OSSemCreate(0); mmc_dma_tx_sem = OSSemCreate(0); request_irq(IRQ_DMA_0 + RX_DMA_CHANNEL, jz_mmc_rx_handler, RX_DMA_CHANNEL); request_irq(IRQ_DMA_0 + TX_DMA_CHANNEL, jz_mmc_tx_handler, TX_DMA_CHANNEL); #endif #endif } static void mmc_send_cmd(struct mmc_request *request, int cmd, unsigned int arg, unsigned short nob, unsigned short block_len, enum mmc_rsp_t rtype, unsigned char* buffer) { request->cmd = cmd; request->arg = arg; request->rtype = rtype; request->nob = nob; request->block_len = block_len; request->buffer = buffer; request->cnt = nob * block_len; printf("mmc_send_cmd: command = %d",cmd); jz_mmc_exec_cmd(request); } static bool inited = false; int _sd_init(void) { if(!inited) { jz_mmc_hardware_init(); wakeup_init(&sd_wakeup); inited = true; } struct mmc_request test; //mmc_send_cmd(&test, MMC_CIM_RESET, 0, 0, 0, RESPONSE_NONE, NULL); mmc_send_cmd(&test, MMC_GO_IDLE_STATE, 0, 0, 0, RESPONSE_NONE, NULL); mmc_send_cmd(&test, SD_SEND_OP_COND, MMC_OCR_ARG, 0, 0, RESPONSE_R3, NULL); return 0; } bool card_detect_target(void) { return jz_mmc_chkcard() == 1; } #ifdef HAVE_HOTSWAP void card_enable_monitoring_target(bool on) { if(on) { } else { } } #endif /* TODO */ tCardInfo* card_get_info_target(int card_no) { static tCardInfo card; return &card; } /* TODO */ int _sd_read_sectors(unsigned long start, int count, void* buf) { (void)start; (void)count; (void)buf; return -1; } /* TODO */ int _sd_write_sectors(unsigned long start, int count, const void* buf) { (void)start; (void)count; (void)buf; return -1; }