#define _PAGE_ Repair Your LCD #include "head.t"

Author: Peter van Hardenberg

My LCD screen broke, I know I'm not alone, so at dwihno's suggestion, I'm typing up this information so everyone else can benefit too.

Okay, your LCD is broken, but the 'box still works. Now what?

PART 1: Getting a new screen

You're going to need a new LCD, but odds are you don't have a clue where to get one.

Part number: G112064-30
Manufacturer: Shing Yih Technologies, Taiwan

Unless you're buying a few hundred, I don't think Shing Yih is going to listen to you. Instead, I recommend you shop at:

http://www.newmp3technology.com/

For me, a replacement LCD was $24USD with shipping. (Archos wants $60 minimum just to look at it.)

PART 2: Disassembling the Frame

This is written up well on the rockbox site, but you will need a #10 Torx bit (check your hardware store) and a small Phillip's head screwdriver to take the box apart.

http://rockbox.haxx.se/mods/disassemble.html

PART 3: Desoldering

There are a total of eight points you will need to desolder. They are three on each side of the metal frame holding the electronics, and two at the top end. The side points are structural, but the top two (which are on either side of the microphone) supply power to the hard drive. I am not going to tell you how to desolder a joint. That is up to you. I found it helpful to use a small tool to lift up the joints as I worked, seperating the side ones individually and then gradually working out the top ones. I certainly hope you are more competant at desoldering than I.

The two electronics boards inside the Archos are connected by a paralell connector, much like the one you find on the back of your hard drives, though without the cable. This is why even desoldered the boards will stick together. Carefully seperate the two boards. They are connected by several wires. Don't break them.

NOTE: The two connections at the top (by the microphone) have wires embedded in them. This won't make your life any easier.

NOTE: If you remove the tape in the battery compartment while you work, make sure you replace it with something afterwards! (A couple strips of simple scotch tape worked for me.)

BE CAREFUL not to break the end boards off while you work!

Again, the rockbox site has some handy pictures, though this section is for the non-recorder model and is a bit uninformative.

http://rockbox.haxx.se/mods/disassemble2.html

PART 3: The New LCD

Remove the old LCD cable. There are two little clips (one on each side of the connector) that can be gently pushed out to free the strip connector. When you put the new LCD in, make sure you have the right orientation (duh) and also make sure the connection is tight before you clip it back down. This part is probably the easiest of the whole affair. Be careful with the plastic frame under the LCD, as it seems a bit fragile.

PART 4: Test!

Don't solder it all back together yet. Re-seat the top electronics board so the parallel connector is snug. (Watch out for those pins by the microphone! Now you can plug the unit into the AC adapter to see if the LCD works. You should get a message on the LCD saying "ATA Error" or something to that effect. This means the LCD is sitting correctly and you can proceed to reassemble. If not, go back to part 3.

PART 5: Resolder

UNPLUG the archos. (Just thought I'd better reiterate.)

Resolder the two top connections (the ones by the mic).

PLUG the archos back in. The hard drive should spin up. Nothing much more will happen until you put the batteries in though. (I think, I can't quite remember.)

Okay, good. Unplug the Archos again.

IMPORTANT: When you resolder the frame points, make sure you don't leave any pointy bits of solder poking into where the batteries run. I did, and they scraped the plastic off my batteries, shorted out against the frame, melted the inside of one of the bumpers a bit (smoking and smelling awfully) and just about scared me to death. This is also why you need to put the tape back on if you removed it.

PART 6: Reassemble the Archos!

Put the archos back together, taking care not to bend anything. The rubber bumpers are tricky, but I think there are some notes on the rockbox site about how to put them on the right way.

Victory at last! You're done! Now go to the rockbox site and update your firmware, I bet it's out of date!

CONCLUSION

In the end, this cost me much less than sending it in to someone qualified, but was also a hell of a lot scarier. I think I learned a few things about my Archos though, and I look forward to trying some of the other mods.

I'm sure there are people out there (real pros) who are horrified at what I have written. Please, correct any mistakes I have made in this document so future 'boxers don't have to go through the hours of stress and strain I did. #include "foot.t"