summaryrefslogtreecommitdiffstats
path: root/docs/BATTERY-FAQ
blob: 70ea6f62446a85fc24ceda62c661e901334f2dc1 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
Q1: Are my batteries charged all the time when connected to my Player/Recorder?
A1: Player: the charging is all done by hardware and the exact functionality
    is hard to determine. It is however not recommended to keep the charger
    connected for more than 10-15 hours if you're not using the unit.

    Recorder: no. The charging algorithm is carefully crafted in to not wear
    out the batteries any more than necessary. If you're using your unit
    connected to the charger most of the time, use the 'deep discharge' option
    to save your batteries somewhat.

Q2: Will keeping my charger connected a long time damage my batteries? Can I
    leave it over night?
A2: There's a deep discharge mode and you can switch trickle charge on and
    off.  If you use your AJB connected to the power supply the whole time,
    select "deep discharge on" and "trickle charge off". If you want to charge
    your AJB over night and take it with you the next day, select "deep
    discharge off" (that it starts charging immediately) and "trickle charge
    on" (that the batteries remain full).

    Trickle charge is needed to keep the batteries full. That's necessary
    because the device will stay powered on and continue to consume some power
    from the batteries (the hardware does not allow running from the charger
    without charging batteries, or powering off with the charger connected).
    The trickle charge time is 12 hours. It should be enough for you to
    disconnect your AJB in this time and turn it off / use it.  However, after
    12 hours of trickle charge, it will turn it off, the batteries are
    discharged and another charge cycle is started.
    
    As the Battery FAQ at http://www.greenbatteries.com/ puts it:

    "A NiMH battery can be charged and discharged hundreds of times, but
    whether that means 200 times or 800 times has a lot to do with how (you
    use it)".

Q3: Does Rockbox charge the batteries more/less/worse/better than the Archos
    firmware?
A3: Player: Rockbox doesn't affect the charging on Players, it is all done
    by hardware logic out of software control.

    Recorder: The whole algorithm is made to carefully charge the batteries
    full and keep them full after that with a trickle charge option. Many
    documents about charge ICs were considered. If you want to know details,
    then look into docs/CHARGING_ALGORITHM. If you have comments, write to
    mail@uwe-freese.de or the Rockbox mailinglist.
    
    Test results with trickle charge (battery capacities measured with an
    external charger, Model "Conrad Electronic Charge Manager 2010", ~100
    EUR):
    
    - after normal charge and top off time: 1798, 1834, 1819, 1815 mAh
    - after normal + top off + trickle charge (12h): 1784, 1748, 1738, 1752 mAh
    - charged with external charger: 1786, 1819, 1802, 1802 mAh

    You can see, whenever you take your AJB with you in the 12h trickle charge
    period, the batteries are at least 97% full. :)
    
Q4: What kind of batteries are there in my factory default Player/Recorder?
A4: Both ship with 1500 mAh NiMH (Nickel Metal Hydride) batteries.

Q5: Is it hard to change the batteries? Does it void my warranty?
A5: It is not very hard - the Archos manual and the FAQ on their web site
    describe how to do it. Their technical support confirmed that replacing
    the batteries with NiMH cells (of different capacities) will not void the
    warranty. Just don't remove the screws.
    
    Some units have been shipped with two sets of batteries, my Recorder 20
    only had one set. Someone actually had Archos send him new batteries free
    of charge after they had weared out, under the warranty.

Q6: How much do replacement batteries cost? Where can I buy them?
A6: http://www.greenbatteries.com sells 1800 mAh NiMH cells at $3.25USD each,
    and I bought 4 of the same GP batteries for 20 euros in an home
    electronics & household appliance store in Finland.  NiMH batteries are
    sold in almost all shops that sell consumer electronics, and in many
    online shops. Browse around. There's a pretty good comparison between
    different battery makes and models at the digital imaging resource site:
    http://www.imaging-resource.com/ACCS/BATTS/BATTS.HTM In Germany,
    www.reichelt.de sells GP 2000 batteries for 2,75 EUR (12/2002).

Q7: What kind of run-time can I expect on a set of fully-charged batteries
    when running Rockbox?
A7: For the stock 1500 mAh cells, from 6 hours to 8 hours, depending on which
    charger was used (see Q3) and the bitrate you use (higher bitrate means
    more harddisk runtime). It depends a lot on the condition of the
    batteries. With 2000 mAh batteries, you should reach about 10 hours or
    more.  We are looking into implementing more battery-saving techniques in
    rockbox to make it rock longer.  If you have a modified AJB with 8 MB, you
    can reach playing times of up to 16 hours with 2100 mAh batteries.

Q8: Can I use different batteries in my Archos? How much playtime would
    I gain by using 1800 mAh batteries instead of the 1500 mAh ones?
A8: Only use NiMH-type rechargeable batteries. It is considered to be safe to
    use NiMH batteries of different capacities though, a lot of people have
    purchaced 1700 or 1800 mAh batteries to replace the stock 1500 mAh cells
    and have the device run a bit longer. 2000 mAh batteries are just
    appearing in shops are equally good to use.
    
    In theory, running time = capacity of batteries / current drawn by device,
    so running time should increase linearly by the capacity, and 2000 mAh
    over 1500 mAh should give 33% longer running time. In practice, the mAh
    ratings are more or less tuned up by the marketing department (think of
    watts on the back of "hi-fi" speakers and amplifiers) and what you
    actually get out of the cells is something else than what is printed on
    them. Check the excellent imaging-resource link above for details!

Q9: Can I use non-chargeable batteries in my Archos?
A9: This is not recommended. The unit has been designed to operate with four
    1.2V batteries producing about 4.8V at most, and using 1.5V alkaline/zinc
    carbon batteries will produce around 6.0V, which will heat up the unit a
    lot more and might even damage it. The Archos manual explicitly tells you
    not to do so.  Also, if you connect the charger, it may even destroy both
    the batteries and the unit.

Q10: Can I use a different charger?
A10: The short answer is: Using a different charger will void your warranty
     and can be dangerous to your unit, so we can not recommend it.
     
     On the other hand, people have successfully used different chargers with
     similar specifications as the stock charger. The charger must have the
     same kind of connector with same polarity (center positive/+).  The
     charger should supply at least 7-8 volts, and if it provides more than
     10V, it probably should be regulated to 10V (do not directly plug it in
     your 12V car battery or it's charger!).  The universal travel charger
     sold by Archos is specified at 12V, 1.2A so that's probably the maximum
     rating you should use.  A good circuit for powering from a car battery or
     other source with a higher voltage would be a 600 mA fuse and a 10V
     regulator like a 7810 of your favourite manufacturer in series.
     
     Inside the Jukebox there is a regulator which limits the charging current
     applied to the batteries. The higher the input voltage, the hotter this
     IC gets. Don't use an input voltage above 12V.  Using lower charging
     voltage < 10V will slow down the charging. But the rockbox charging
     algorithm should work then, too.

     These are the output voltages of an original archos power supply:
     - connected to AJB Recorder, not charging: 13,7 Volt
     - connected to AJB Recorder, charging: going down to 10,4 Volt

     Here is how changing the input voltage changes the charging current:

      voltage   charging current (limited only by the AJB)
      ------------------------------------------------------
      7,0V          10 mA
      7,5V          30 mA
      8,0V          50 mA
      8,5V          70 mA
      9,0V         140 mA
      9,5V         250 mA
      10,0V        330 mA
      10,5V        350 mA
      11,0V        350 mA
      11,5V        350 mA
      12,0V        350 mA
     
     To summarize:

      - do not use an input voltage > 12V (it will only heat up the regulator)
      - optimal input voltage is 10V (regulated)
      - use a fuse of ~600mA
      - using a different charger voids your warrenty
     
     Many people are happy using an external quick charger which is specified
     to work with NiMH batteries. This is completely safe and will not void
     your warranty.

Q11: Can I buy a replacement charger exactly as the one Archos shipped?
A11: The FAQ on the Archos web site and the top of the charger both read:

      Output: 9VDC 600mA
      Center positive (+) polarity
     
     The universal travel charger sold separately on the Archos web site is
     specified for 12VDC, 1200mA output.
     
     Chargers with similar (or user-adjustable) properties are available at
     shops selling consumer electronics.

Q12: I often need to stop my player for about 15 minutes or so, and when I do
     it runs off it's batteries.  I was wondering, which is best: shutting the
     player down completely and rebooting it when I want to listen again, or
     leaving the unit on?  Which way does it draw more power?
A12: In our testing we found the following results:
         HDD off, backlight off, idle 94 mA
         HDD off, backlight off, play 97 mA
         HDD off, backlight on, idle 129 mA
         HDD off, backlight on, play 131 mA
         HDD on, backlight on, play 230 mA
         HD on, reading, backlight off ~ 600 mA
         HD spin up before read max 800 mA

     Using the power draw measurements shown above, lets look at the numbers:
     Power-down and restart vs. paused for 15 minutes.:

     Pause for 15 minutes will draw: 94 mA / 60 minutes * 15 minutes =
     23.5 mAh.

     Power-down and restart will draw about (800mA / 3600 seconds * 3
     seconds = 0.6666 mAh) + (600 mA / 3600 seconds * 6 seconds = 1.0 mAh) +
     (230 mA / 3600 seconds * 8 seconds = 0.5111 mAh) = 2.18 mAh total used.

     Thus, leaving it paused for 15 minutes draws more power (23.5 mAh) than
     turning off and then on again (2.18 mAh).

     So where is the break-even point?

     Each second of pause will draw about 94 mAh / 3600 seconds = 26 µAh.

     2.18 mAh / 26 µAh = 2180 µAh / 26 µAh = 83.5 seconds

     Thus a shutdown and restart uses as much power as 83.5 seconds of pause.

Q13: When I plug in the charger when the Recorder is turned off, it turns
     itself on and starts charging in the Archos software? What's up?
A13: There is a switch in the DC IN jack of the Jukebox - when a charger (or
     whatever) is plugged in, the unit is powered on, even if the charger is
     not plugged in a mains outlet.
     
     If the charger is providing power at this point, the Archos firmware
     located on the FLASH ROM does not load a new firmware version (like
     Rockbox) from the disk, but goes into charging mode instead. You can use
     this feature to get to the Archos charger if you want to.

     However, if you put Rockbox in flash, it will always charge with the
     Rockbox charging algorithm.

Q14: When I plug the charger in my Recorder, it doesn't immediately start
     charging the batteries!
A14: When Rockbox is running on the Recorder (the device has been booted
     without the charger) it's power management code runs once per minute
     (thus the charge level and charging status is only updated every minute).
     If the battery is not full, it will start charging. If the 'deep
     discharge' mode is enabled in the settings menu, it will start charging
     only when the battery is almost empty.

Q15: What about the memory effect? Should I be worried about it or not?
A15: That depends on who you ask. ;-) NiMH sellers say NiMHs are better and do
     not have a memory effect, but the usual opinion seems to be that they do,
     although it is very small.
     
     However, if you use your AJB connected to the charger all the time,
     we recommend you to use the deep discharge option.

Q16: When I start my Jukebox, (dis)connect the charger and browse through the
     directories, the battery level changes a little bit. Sometimes it's even
     going up without the charger is connected! What's wrong?
A16: Nothing's wrong. The battery level is calculated out of the voltage.
     Because disk spinning, LED backlight, charger all influence the actual
     battery voltage, it is usual that the battery level is going a little bit
     up and down sometimes. This cannot be avoided although we tried to make
     the battery level display as little confusing as we could.

Q17: My batteries are at 92%, the charger is connected to my recorder, deep
     discharge is off. But charging doesn't start. What's wrong?
A17: Charging starts if the battery level is below 85%. This is because
     charging batteries that *are* already more or less full is not good for
     the batteries and the end of the charging cycle can't be detected safely.
     So it's better to start at a level at least as low as 85%.  If you want
     to have full batteries in the morning, leave the charger connected over
     night. Charging will then start some hours later. The second possibility:
     Use the Archos charging algorithm. At least, your batteries will be full
     one more time. ;-)

Q18: Why does rockbox show a question mark for the battery level?
A18: Rockbox waits for about a minute to show a battery reading, to increase
     the reliability of the reading. In previous versions, the battery level
     rockbox initially reported was always too low.